Quick answer: A Portable calibrator heavy duty safety box pairs a 5.2 mm wall with 95 mm corner wraps, holding dent under 1.0 mm after a 1.5 m drop.
Table of contents
- Layered wall thickness of a Portable calibrator heavy duty safety box
- Corner wrap coverage length
- Dent readings after a four-corner drop
- Lid pressure drop in the air-tightness recheck
- Wall thickness grading for the reinforced batch
- FAQ
1. Layered wall thickness of a Portable calibrator heavy duty safety box
For a Portable calibrator heavy duty safety box, a corner drop lands on the wrap first; when the wrap is too short, the reinforced layer absorbs the remaining dent through its own stiffness. The outer 540 by 390 by 220 mm and inner 470 by 325 by 155 mm leave a nominal 5.2 mm wall split into a shape-holding base layer and an impact-taking reinforced layer. The reinforced layer runs around all four walls, guiding corner force into the wall before the base layer spreads it across two adjacent faces.
On the rig at 23 °C / 50% RH, three shell grades from one mould are logged: each step up raises the empty 6.1 kg mass and shrinks the inner clearance, and both sit beside the dent reading rather than being reported selectively. The grading sheet for a Portable calibrator heavy duty safety box sets wall thickness, mass and clear dimension side by side; a missing column is not a grade.
| Wall thickness grade | Reinforced layer | Largest dent after drop |
|---|---|---|
| Thin | 4.4 mm | 1.4 mm |
| Nominal | 5.2 mm | 0.8 mm |
| Thick | 6.0 mm | 0.6 mm |
The thin grade crosses the 1.0 mm criterion, the thick grade reaches 0.6 mm but adds mass, so the nominal grade becomes the batch reference, read at one position under one rig.
2. Corner wrap coverage length
The 95 mm corner wrap is the second grading quantity for a Portable calibrator heavy duty safety box on this mould. It is a continuous band along three edges, and its length sets how far the corner load spreads; at 95 mm the 1.5 m drop energy is distributed before the wall middle, while a shorter wrap lets the force gather back at the corner as a pit.
On a Portable calibrator heavy duty safety box, wrap and reinforced layer work as a pair: thicken the wall and shorten the wrap, and the dent moves to the corner; lengthen the wrap without layering, and the impact travels farther along a deforming wall. The 4 corners are numbered, the wrap-to-wall step is measured after each drop, and 4 latches at 410 N each are logged in the same step, since they decide whether the lid gives way before the wall at impact.
3. Dent readings after a four-corner drop
On a Portable calibrator heavy duty safety box the 1.5 m / 4-corner sequence alternates diagonally, so adjacent corners never stack deformation on one face. After each drop the shell settles, a straightedge reads the deepest point, and the largest of the four corners becomes the dent value, judged against 1.0 mm.
| Drop corner | Drop height | Dent value at that corner |
|---|---|---|
| Corner one | 1.5 m | 0.7 mm |
| Corner two | 1.5 m | 0.8 mm |
| Corner three | 1.5 m | 0.6 mm |
| Corner four | 1.5 m | 0.8 mm |
For a Portable calibrator heavy duty safety box, the largest readings sit at corner two and four, both 0.8 mm, so the 95 mm wrap has spread the load rather than piling it at one corner. A repeat drop at the loaded 13 kg mass is run once more; a rise over 0.2 mm means the load has consumed the wall grade margin.
4. Lid pressure drop in the air-tightness recheck
A dropped Portable calibrator heavy duty safety box is not released straight away; an air-tightness recheck runs on the same shell. The lid pressure drop criterion is 0.3 kPa / 10 min, measuring whether 2 seals at 21% compression still close after the drop shifts the lid against the gasket at 23 °C / 50% RH. Shells after 4000 open-close cycles pass the same step, and IP67 is logged as a benchmark method, not a grade already obtained.
| Dent value | Recheck lid pressure drop | Decision |
|---|---|---|
| 0.6 mm | 0.22 kPa / 10 min | Release |
| 0.8 mm | 0.26 kPa / 10 min | Release |
| 1.0 mm | 0.31 kPa / 10 min | Reject |
The rows tie dent value to pressure drop: at 1.0 mm the drop nears the 0.3 kPa ceiling, so both criteria tighten together and wall deformation has reached the sealing face. A Portable calibrator heavy duty safety box only earns a clean recheck after the four-corner drop; a pass without a dent reading does not count.
5. Wall thickness grading for the reinforced batch
For a Portable calibrator heavy duty safety box, pulling the readings together gives one closing line. Wall thickness grading takes the grade before the one where dent first reaches 1.0 mm as the reference, and any thinner shell moves wholesale to the non-reinforced specification. The empty 6.1 kg, loaded 13 kg, 4000 cycles and 4 latches at 410 N are boundary conditions frozen onto the grading sheet, so a new mould reruns the four-corner drop and recheck.
Grading is not settled by one reading. Every sampled shell reports wall thickness grade, wrap coverage, largest four-corner dent and lid pressure drop, and only when all four land in the same grade does it join the reinforced specification. A crossed line marks that shell for its own recheck, never covered by another shell reading. Records for a Portable calibrator heavy duty safety box are filed by rig condition, and drawing tolerances follow.
Conclusion
A Portable calibrator heavy duty safety box is graded not by one thickness figure but by the loop of reinforced layer, corner wrap and drop recheck. The 5.2 mm wall, 95 mm wrap and 1.0 mm dent limit sit on one configuration sheet, with lid pressure drop as the cross-check. JUNZHIJIA keeps rig records of 4000 open-close cycles on the reinforced batch, and Kexin New Materials (Guangdong) Co., Ltd. issues drawing tolerances from them.
Related Reading
- Instrument case series: precision, testing, analysis, measurement and calibration cases
- How to choose a precision instrument protective case: shock and moisture protection
- Laboratory instrument case transport: shock protection and post-calibration recheck
- Portable spectrum analyzer sealed safety case
Related Products
- 8 Series — Gun Cases; Military Equipment Cases; Camera Equipment Cases; Drone Cases; Watch Cases; Knife Cases; First Aid Cases; Electronics Equipment Cases
- WL8-2812 PP Gun Case — model WL8-2812
- All protective cases and toolboxes: 7 series, 158 models