How is the 500 piece MOQ for a firearm plastic gun case wholesale order calculated?

Answer: Changeover time: 3.5 hours adds 1.5 per piece at 500 units, 3.7 at 200.

Should tooling be charged separately or spread into the price?

Answer: Spread it for one run; charge it separately on repeat orders and state ownership.

A quote is 30 lower than the others; what do I check first?

Answer: Wall, then latches: 3.0 to 2.4 mm saves 6 in resin, two latches save 7 in hardware.

Can the 8,000 piece price go lower?

Answer: Only through the tool: a 1×4 layout gives 4.6, but CNY 410,000 needs 30,000 pieces to pay back.

Is the 28 day sea transit port to port?

Answer: Yes, to a US West Coast base port, without drayage; door to door adds 9 days.

Firearm Plastic Gun Case Wholesale: Quote, MOQ and Lead Time

Quick answer: A firearm plastic gun case wholesale quote should be split into cavity size, wall, latch count and liner, because vague wording costs more than a high price. A 780 tonne press on 1×2 cavities puts the economic batch at 500 pieces, and lead time reports in four blocks, from 6 working days for samples to 28 days by sea.

Six Figures a Firearm Plastic Gun Case Wholesale Quote Must Carry
How Price Follows Tonnage and Cavity Count
MOQ, Mould Ownership and First Article Approval
Acceptance and Batch Traceability in the Contract
Lead Time in Four Blocks and Route Choice
FAQ

1. Six Figures a Firearm Plastic Gun Case Wholesale Quote Must Carry

A purchase pack is not an inquiry form; it makes three plants quote the same object. One body may return 96 and another 118, only 4 of it margin.

Line	Figure required	Cost if vague
Internal size	plus or minus 1.0 mm	mould change, CNY 24,000
Wall	3.0 mm body, 2.6 mm lid	0.5 mm thinner
Latches	four, 60 N each	a 35 N pair
Seal	6 mm groove, 5.5 mm cord	rain in 30 minutes
Heat	minus 20 to 60 C	sag at 65 C
Drop	12 kg at 1.2 m	corner cracks

Latch force matters most: 35 N pops open on the first 1.2 m drop.

2. How Price Follows Tonnage and Cavity Count

A firearm plastic gun case wholesale price is calculated on the press: a 780 tonne machine on 1×2 cavities runs a 105 second cycle, 68 pieces an hour theoretical and 34 net, so CNY 210 an hour gives 6.2 per piece.

Firearm plastic gun case wholesale: black case open, blue corner guards, black foam tray with screen recess, coiled leads

Batch	Cavities	Cycle	Unit price
500 pcs	1×1	128 s	CNY 118
2,000 pcs	1×2	105 s	CNY 104
8,000 pcs	1×2	96 s	CNY 96

Material is 4.6 kg times a 1.06 loss factor, so PP at CNY 10.6 a kilo gives 51.7; hardware 8, liner 12 and packing 3 put cost near 81. That 14 gap is press time spread wider.

3. MOQ, Mould Ownership and First Article Approval

The 500 piece minimum is arithmetic. A changeover takes 3.5 hours and a 780 tonne press runs two specifications a day, so 500 pieces fill under two shifts; below that a plant charges CNY 1,200 per changeover or pushes the price past 130.

A 1×2 tool costs CNY 260,000, adding 520 per piece at 500 units and 32.5 at 8,000. Ownership must be written down: bought out, or shared with a 15 day queue for colour changes and CNY 90,000 off the tool.

After the T1 trial, measure nine dimensions including cavity length, width, depth and latch centre distance; three trials sit inside the tooling price, then CNY 6,000 each.

4. Acceptance and Batch Traceability in the Contract

The real risk in volume is drift: the first 100 pieces run 3.0 mm wall, the last 200 fall to 2.5 mm.

Firearm plastic gun case wholesale: close view of black rim and raised lid, hinge at left, grey pebble-textured foam with a square recess

Item	Sample	Limit
Wall	20 pcs, 8 points	2.4 mm minimum
Latch force	20 pcs	45 to 75 N
Drop	3 pcs	1.2 m, no through crack
Salt spray	10 parts	96 hours, white rust under 5 percent

Traceability needs a mould number and a shift code, both moulded in the compound. Colour drift is held at Delta E 1.8, past which two batches read as two models.

5. Lead Time in Four Blocks and Route Choice

A firearm plastic gun case wholesale lead time given as one number swallows every risk. Report four blocks: 6 working days for samples, 22 days for tooling, 16 to 20 days for production, 28 days by sea to a US West Coast base port.

Tooling is least controllable, with steel returning in 12 days and CNC scheduling taking 6; expediting to 17 days adds 18 percent, two production runs save 5 days, and rail takes 20 instead of 28.

Conclusion

Buying firearm plastic gun case wholesale means turning one total price into three checkable columns: written cavity and wall figures, a batch size that matches the press, and a lead time quoted in blocks. Six figures pull a forty percent spread down to ten and keep cash out of stock, so firearm plastic gun case wholesale stops depending on arguments after delivery.

This article discusses only the container (case body) side of specifications and design intent, and does not cover any handling, loading or use of the contents.