Quick answer: A heavy generator maintenance tool hard box measures 900 × 380 × 260 mm, with three 820 mm long-tool bays and a 32 kg heavy-load tier.
Table of contents
- Why a Heavy Generator Maintenance Tool Hard Box Fights Its Own Length
- Long-Tool Bays and Cross Dividers
- Stacked Trays and the Order of Access
- Weight Tiers and the Two-Person Carry
- Base Ribs and the Drop
- FAQ
1. Why a Heavy Generator Maintenance Tool Hard Box Fights Its Own Length
The longest socket extension in a generator hall decides how long the case must be. Extension bars push storage to 900 mm while daily tools fill a third of the interior, so this heavy generator maintenance tool hard box ends at 900 × 380 × 260 mm outside.
The 850 × 330 × 220 mm cavity is the compromise. Three bays take 820 mm each, leaving 15 mm at either end for stops, and short tools sit in the strip beside them; stacking over the bars means lifting a layer before each long tool.
Length moves the centre of gravity as well. An 820 mm bar laid along one side pushes it 40 mm off the middle, and a heavy generator maintenance tool hard box leans that way as two people lift it. A 5.5 mm wall plus 5 base ribs carries the offset.
Overhauls happen in unheated garages, so −20 °C to +60 °C is the band. Homopolymer PP embrittles at −5 to −15 °C and falls to 1–2 kJ/m² at −20 °C, so the body is block copolymer, ductile to −25 to −45 °C.
2. Long-Tool Bays and Cross Dividers
A long-tool bay on a heavy generator maintenance tool hard box is not one open channel. Three 820 mm slots at 46, 34 and 22 mm split bars, torque bars and long bits; each floor is half-round, so nothing rolls into the next slot.
2 cross dividers cut the 850 mm cavity into 300, 350 and 200 mm. Moulded with the base, 4 mm thick, with a 30 mm finger gap at 60% of cavity depth.
A divider between slots in a heavy generator maintenance tool hard box gives each a mid-support: an 820 mm bar bends over 350 mm, not 820 mm, and mid-deflection drops by half.
| Long-tool bay | Width | Floor | Bar length |
|---|---|---|---|
| Wide slot | 46 mm | R23 half-round | 780–820 mm |
| Middle slot | 34 mm | R17 half-round | 700–820 mm |
| Narrow slot | 22 mm | V-groove 90° | 600–820 mm |
3. Stacked Trays and the Order of Access
Two trays sit 120 mm above the bays, rated 12 kg per layer, both lifting out whole on a 45 mm rim.
Height sets the order: trays and hangers take 75 mm of the 220 mm cavity, leaving 145 mm over the bars, so a bar needs the upper tray on the lid ledges first; short tools need only that tray.
Only 8 mm separates tray bottom from bar top, and a 3 mm recess in the underside grid clears the anti-roll boss on every pull.
4. Weight Tiers and the Two-Person Carry
A heavy generator maintenance tool hard box weighs 18.5 kg empty with trays and lining, and the 32 kg heavy tier leaves 13.5 kg for tools.
ISO 11228-1 puts ideal two-handed lifting at 25 kg per person; a pair is derated 25% to 37.5 kg, so 32 kg keeps 5.5 kg for the acceleration of a lift.
The table answers the floor question: how many people. One person lifts 18.5 kg, shifts 24 kg a short way, and calls for help past 28 kg.
| Weight tier | Case weight | Tool payload | Handling |
|---|---|---|---|
| Light | 18.5–24 kg | 0–5.5 kg | One hand |
| Standard | 24–28 kg | 5.5–9.5 kg | One person, or one end each |
| Heavy | 28–32 kg | 9.5–13.5 kg | Two people, 16 kg per side |
Posture fails sooner than the rating: a handle plus a base support bows the body, while both ends turns 3 latches rated 450 N into shear joints.
| Carry posture | Per side | What the shell sees | Tier |
|---|---|---|---|
| Both ends | 16 kg | Walls in tension | Heavy |
| Handle plus base | Over 20 kg | Lid panel in bending | Standard |
| Sling under base | None | Ribs compressed | Heavy |
The handle on a heavy generator maintenance tool hard box is moulded with the body and a 10 mm root; at 16 kg per side the fingertips fail first, so the section is oval.
5. Base Ribs and the Drop
Five ribs run the 900 mm length at equal spacing, 14 mm tall, dying into the corners with the middle three under the bays. 4 caster pockets sit inboard of the corners and clear of the ribs.
The drop is 1.0 m at a corner. ISTA 3A gives 460 mm under 32 kg; 1.0 m is stricter because long cases travel stood on end; a through-crack in the corner rib ends the test.
3-high stacking on a heavy generator maintenance tool hard box is the ceiling. At 18.5 kg empty the bottom lid carries 37 kg for weeks, so lid ribs must line up with base ribs.
IP65 is dust-tight plus a 6.3 mm nozzle at 12.5 L/min from 2.5–3 m for at least 3 min, which covers a hose-down rather than immersion.
Conclusion
Length, weight and floor form one chain: 820 mm bays set the 900 mm outside, the 18.5 kg empty weight and 32 kg tier split the lift, and five ribs with a 1.0 m corner drop decide whether a corner survives.
Related Reading
Related Products
- 8 Series — Gun Cases; Military Equipment Cases; Camera Equipment Cases; Drone Cases; Watch Cases; Knife Cases; First Aid Cases; Electronics Equipment Cases
- WL8-2812 PP Gun Case — model WL8-2812
- All protective cases and toolboxes: 7 series, 158 models