Quick answer: A Broadcast AV switcher protective case keeps lid sag under 0.7 mm after 5000 cycles when 0.28 mm pin-bushing clearance and 100 degree opening angle hold.
Table of contents
- Pin-bushing clearance of the Broadcast AV switcher protective case
- Mismatch at the parting line of the case mouth
- Lid sag across opening cycles
- Opening angle rechecked under full load
- Clearance close-out value for broadcast batches
- FAQ
1. Pin-bushing clearance of the Broadcast AV switcher protective case
Lid sag is the net remainder after pin-bushing clearance and parting-line mismatch have shared the weight of the lid. A Broadcast AV switcher protective case uses two through-pins and four pressed bushings set into the lid ears and body ears; the radial gap between pin and bushing is the clearance here. Too little gap makes opening stiff and wears the bore; past 0.28 mm the lid mass presses the bushing down at every close.
Measure it by laying the shell flat on a jig and running a feeler gauge along each bushing at three sections, turning 90 degrees at each and recording the largest value. On a 660×470×280 mm outer shell the lid arm is long and the clearance spread has to be read on its own. A Broadcast AV switcher protective case sets its wall at 4.9 mm, with the bushing seats in a locally thickened lid ear.
| Clearance step | Measured bushing gap | First-cycle sag |
|---|---|---|
| Tight step | 0.22 mm | 0.31 mm |
| Base step | 0.28 mm | 0.48 mm |
| Loose step | 0.35 mm | 0.72 mm |
First-cycle sag is read after 500 cycles at the lid front midpoint. The tight step sags least but opens stiff; the loose step reaches 0.72 mm and has crossed the 0.7 mm line.
2. Mismatch at the parting line of the case mouth
Mismatch is the offset between lid mouth and body mouth on the parting face; it is neither clearance nor lid sag. A Broadcast AV switcher protective case holds mismatch at or below 0.45 mm so two seal rings compress evenly around the loop, a figure that belongs in the same judgement when the seal target is benchmarked to IP66.
Measure it with a dial indicator around the mouth edge; the spread between the highest and lowest reading is the mismatch. On a 590×405×205 mm inner cavity the midpoint of the long side gives way most easily and earns an extra reading. A Broadcast AV switcher protective case reads both the 8.2 kg empty and 19 kg loaded shell, and the loaded round governs delivery.
3. Lid sag across opening cycles
Sag accumulates, and its slope only appears past 2000 cycles. A Broadcast AV switcher protective case sets 5000 cycles as the end point, stopping every 500 cycles to read the lid front midpoint and joining nine or ten points into a curve. The slope of the whole curve has to flatten in its last stretch.
| Opening cycles | Base-step sag | Loose-step sag |
|---|---|---|
| 500 | 0.48 mm | 0.72 mm |
| 2000 | 0.55 mm | 0.88 mm |
| 3500 | 0.61 mm | 1.02 mm |
| 5000 | 0.66 mm | 1.19 mm |
The base step moves from 0.48 mm to 0.66 mm, gaining only 0.05 mm per 1500 cycles at the end; the loose step reaches 1.19 mm and never stops. The rule of sag at or below 0.7 mm after 5000 cycles keeps the base step and rules the loose step out. Recheck after a 1.0 m drop, where a 0.03 mm jump is logged into the curve, and verify the four 440 N latches every 1000 cycles because clamp decay inflates the reading.
4. Opening angle rechecked under full load
Opening angle is where the raised lid comes to rest, and a Broadcast AV switcher protective case sets 100 degrees as the recheck line. Loose bushings let the lid settle back and the angle shrinks; a skewed mismatch makes the lid rub the mouth and the angle stays low too.
For the recheck, load the shell to 19 kg, lift the lid to its resting position and read the angle with a protractor. Beyond 100 degrees the lid falls open under its own weight; below 100 degrees it springs back during access. Two seal rings at 22 percent compression are verified here too, since sag eats a share of the compression. The recheck of a Broadcast AV switcher protective case refits bushings on the original box, and restoring 100 degrees while 5000-cycle sag stays at or below 0.7 mm qualifies one hinge combination.
5. Clearance close-out value for broadcast batches
Before a batch ships, one close-out value pulls the trialled hinge steps down to a single step. The close-out value is the step immediately before sag first reaches 0.7 mm, and one step looser is returned as a whole batch. On the record sheet this becomes a number: the 0.28 mm base step is kept, the 0.35 mm loose step returned, and the 0.22 mm tight step logged as a trend only.
| Sag value | Matching clearance step | Batch disposition |
|---|---|---|
| ≤0.48 mm | Tight step 0.22 mm | Log only, not tabulated |
| 0.48–0.66 mm | Base step 0.28 mm | Whole batch released |
| ≥0.72 mm | Loose step 0.35 mm | Returned for retooling |
Setting it means overlaying the sag curves from three trial fitting rounds and closing on the step whose slope flattens and whose end point stays at or below 0.7 mm. The Guangdong moulding plant files the record under this rule, and every JUNZHIJIA batch of the Broadcast AV switcher protective case carries the curve card. Bore spread between incoming lots shifts one clearance step by about 0.02 mm, so the value is re-pointed per lot.
Conclusion
Lid sag in a Broadcast AV switcher protective case comes down to how pin-bushing clearance and parting-line mismatch share lid weight across 5000 cycles. A 0.28 mm gap paired with mismatch at or below 0.45 mm keeps sag inside 0.7 mm and the opening angle steady at 100 degrees. Judge a batch by whether the whole curve flattens, not by one end reading. Written onto the inspection card, this gives the hinge combination of a Broadcast AV switcher protective case a single release basis.
Related Reading
- Film and broadcast equipment cases: heavy loads, flight schedules and fast turnaround
- Portable OB equipment trolley case for broadcast use
- Monitor and video transmitter protective case
- Camera equipment case guide: sizing, foam cushioning and moisture control
Related Products
- 8 Series — Gun Cases; Military Equipment Cases; Camera Equipment Cases; Drone Cases; Watch Cases; Knife Cases; First Aid Cases; Electronics Equipment Cases
- WL8-2812 PP Gun Case — model WL8-2812
- All protective cases and toolboxes: 7 series, 158 models