Quick answer: The Flaw detector portable shockproof protection latch box pairs an 18 mm slot with a 4.6 mm stroke, holding shift to 0.9 mm after a six-face drop.
Table of contents
- Flaw detector portable shockproof protection latch box: the slot-depth baseline
- How the 4.6 mm latch take-up stroke is split
- Displacement readings after a six-face drop
- Slot-mouth recovery in the cold retest
- Slot-depth convergence across a hand-carry batch
- FAQ
1. Flaw detector portable shockproof protection latch box: the slot-depth baseline
Hand-carried impact is absorbed first at the corners, so the displacement left over depends on whether liner slot depth and latch stroke agree. The Flaw detector portable shockproof protection latch box measures 520x380x210 mm outside; minus the 4.2 mm wall, its cavity is 455x315x145 mm and the locating slot is cut into that floor. The gap between an empty 4.8 kg and a loaded 9 kg is why the slot walls are machined to full-load sag, not to the empty shell.
| Slot depth grade | Clear slot depth | Matched stroke | Shift after six-face drop | In selection table |
|---|---|---|---|---|
| Shallow | 15 mm | 4.6 mm | 1.3 mm | No |
| Middle | 18 mm | 4.6 mm | 0.7 mm | Yes |
| Deep | 21 mm | 4.6 mm | 0.5 mm | No |
The shallow grade breaks 0.9 mm at 1.3 mm; the deep grade reaches 0.5 mm only by squeezing away the lid relief.
2. How the 4.6 mm latch take-up stroke is split
The Flaw detector portable shockproof protection latch box uses two latches rated at 360 N each to use up the 4.6 mm take-up stroke. The first part consumes the 19% seal compression, the second brings the lid pad onto the liner slot, and both are calibrated together with the 18 mm slot. Two latches sit along the 520 mm long edge; we check only the 0.3 kPa / 10 min airtightness grade and benchmark the shell against IP66. After 3600 cycles a shortened stroke leaves the pad hanging free and the displacement drifts.
3. Displacement readings after a six-face drop
The 1.2 m six-face drop runs over base, lid, two long edges and two short edges, and the Flaw detector portable shockproof protection latch box is measured for seat shift after every face. We read the string of six figures, not one peak: a grade holds only when two consecutive faces stay below 0.9 mm. Mouth loss is taken at the same time, with 0.3 kPa / 10 min as the sealing floor.
| Drop face | Impact surface | Probe-seat shift | Mouth pressure loss | Slot-mouth state |
|---|---|---|---|---|
| Base | Bottom | 0.4 mm | 0.1 kPa | No gap |
| Long edge one | Side wall | 0.7 mm | 0.2 kPa | Slight gap |
| Long edge two | Side wall | 0.6 mm | 0.2 kPa | Slight gap |
| Lid | Cover | 0.8 mm | 0.3 kPa | Recovered |
On the Flaw detector portable shockproof protection latch box, the face order is not arbitrary. The base lands first and corners swallow the shock, leaving the slot almost still. Roll onto a long edge and the shock crosses the 520 mm span, pushing the seat slightly to one side. The opposite edge is often symmetric but not equally deviated, which is why both must be read. The lid lands last, and this face shows best whether recovery pulls the shift back. Across the six figures, the 18 mm grade gives 0.7 mm and 0.6 mm on the long edges, two consecutive faces under 0.9 mm, landing exactly on the convergence line.
4. Slot-mouth recovery in the cold retest
Passing the room-temperature round is not the end: the Flaw detector portable shockproof protection latch box is soaked at -20 C and retested. Cold stiffens the foam and contracts the seal, so slot-mouth recovery shrinks and a grade that held 0.9 mm may lose margin. All six faces are remeasured with loss still held to 0.3 kPa / 10 min. At -20 C the foam modulus rises and the mouth may not follow, so an 18 mm slot returning to 0.7 mm warm may only reach 0.95 mm cold.
| Shift reading | Matched slot grade | Cold-retest recovery | Convergence call |
|---|---|---|---|
| 1.3 mm | Shallow | Short | Rejected |
| 0.7 mm | Middle | On target | Kept |
| 0.5 mm | Deep | On target | Not listed |
5. Slot-depth convergence across a hand-carry batch
Slot depth never lands neatly on 18 mm across a batch; a few shells drift to 17 mm or 19 mm. The Flaw detector portable shockproof protection latch box is filed by measured depth, then matched against the six-face and cold readings to find the band holding both 0.9 mm and 0.3 kPa / 10 min, with 4.8 kg and 9 kg logged alongside.
The converged slot depth is the shallowest grade whose shift stays below 0.9 mm on two consecutive faces; deeper grades are left out of the selection table.
With that line fixed, the deep 21 mm grade stays off the delivery list despite reaching 0.5 mm, because it consumes the lid relief. The middle 18 mm grade alone keeps margin across the six faces, the cold soak and 3600 cycles, so the batch card is issued against it.
Conclusion
The Flaw detector portable shockproof protection latch box ties slot depth, take-up stroke and post-drop shift into one chain that can be rechecked, with 18 mm and 4.6 mm on the structure and 0.9 mm and 0.3 kPa / 10 min on the test rig. The -20 C soak and 3600 cycles filter out the recovery loss and stroke decay a room-temperature reading hides. A batch issued against this convergence value keeps a single middle grade in the selection table.
Related Reading
- IP67 waterproof NDT instrument protective case
- Detection instrument cases: field protection and storage
- 3D scanner portable shockproof hard safety case
- Custom EVA foam lined precision instrument case
Related Products
- 8 Series — Gun Cases; Military Equipment Cases; Camera Equipment Cases; Drone Cases; Watch Cases; Knife Cases; First Aid Cases; Electronics Equipment Cases
- WL8-2812 PP Gun Case — model WL8-2812
- All protective cases and toolboxes: 7 series, 158 models