Quick answer: Military injection molded container source factory OEM keeps lid warp under 0.9 mm and groove spread under 0.25 mm across 3 shifts at 68 °C.

Table of contents

  • Mold Temperature Zones in a Source Factory OEM Program
  • Where the Hold-Pressure Switchover Is Sampled
  • Lid Flatness After the Third Shift
  • Repeat Readings of Groove Depth
  • Mold Temperature Release Values for Contract Batches
  • FAQ

1. Mold Temperature Zones in a Source Factory OEM Program

Three shifts on one tool keep the lid flat only if mold temperature zones and the hold-pressure switchover do not drift together. Military injection molded container source factory OEM runs three water circuits on this 640×460×280 mm shell, cavity 570×395×210 mm and wall 4.7 mm, holding the lid circuit half a step below the side walls at 68 °C so the lid chills before ejection.

The lid centre and its four edges cool at different rates, so a shared return lets centre heat drag the edges and bow the lid after demolding. Routing the lid circuit alone to the 68 °C baseline lets warp settle, and JUNZHIJIA files this zoning set as the internal baseline for a contract batch.

Mold temperature gradeLid circuit setupThird-shift lid warp
Baseline 68 °CSeparate return, chilled first0.62 mm
One grade higherShared return with side walls0.94 mm
Half grade lowerEarly ejection0.71 mm

Of the three grades the baseline warps least, the higher grade crosses the line through mixed return water, and the lower grade springs back overnight on trapped heat. Military injection molded container source factory OEM pins the lid circuit at 68 °C and keeps the side-wall grades from being mixed on one tool.

2. Where the Hold-Pressure Switchover Is Sampled

Switchover at 96% fill leaves the last cavity stretch to holding pressure. Military injection molded container source factory OEM triggers it by screw position rather than a timer, because melt viscosity drifts with stock temperature; holding then rises to 42 MPa and cooling runs 26 s, which decide whether the thin groove ring is packed level.

Military injection molded container source factory OEM black wheeled cases in a showroom row, tall orange shell at left and a visitor waving
Military injection molded container source factory OEM black wheeled cases in a showroom row, tall orange shell at left and a visitor waving

Six groove points, the four corners plus the two long-edge midpoints, take the clamping force of 4 latches at 425 N each first and carry the 2 seals at 21% compression. Reading all six rather than one midpoint exposes the depth spread the switchover must feed, and the IP67 spray check follows this same groove for a continuous compressed edge.

3. Lid Flatness After the Third Shift

Three consecutive shifts are the observation window for this tool. Military injection molded container source factory OEM takes three shells per shift, 7.6 kg empty and 20 kg loaded, lays them on a bench and reads the largest lid gap with a feeler gauge; the first shift is flattest, the third shows the drift.

Shift numberShells sampledLargest lid gap
First shift3 shells0.41 mm
Second shift3 shells0.68 mm
Third shift3 shells0.88 mm

The reject line sits at third-shift lid warp ≤0.9 mm, where 0.88 mm passes against it and the 0.94 mm grade returns to the trial record. Military injection molded container source factory OEM will not release on the first-shift numbers, because stacked shells turn a bowed lid from area pressure into a single line of contact.

4. Repeat Readings of Groove Depth

A groove depth spread ≤0.25 mm is the gap between the deepest and shallowest of six lid points, not a deviation from the design value. Military injection molded container source factory OEM rests the shell 4 h before the repeat check, since an out-of-line spread makes the 2 seals tighten and loosen around the perimeter.

Military injection molded container source factory OEM injection moulding machine with overhead hopper, green drum and polypropylene sacks below red ceiling pipes
Military injection molded container source factory OEM injection moulding machine with overhead hopper, green drum and polypropylene sacks below red ceiling pipes

A dial calliper logs only the maximum and minimum of the six points; reading them again after 4100 open-close cycles shows whether latch clamping has collapsed a groove edge. Military injection molded container source factory OEM compares the two spreads and rechecks the 96% fill switchover if the later set grows by more than 0.05 mm.

5. Mold Temperature Release Values for Contract Batches

The release value is locked to the lowest grade whose third-shift warp still holds 0.9 mm, and any set one grade higher is returned wholesale to the trial record. Military injection molded container source factory OEM freezes the lid circuit 68 °C, holding 42 MPa and cooling 26 s on the process card before a contract batch starts.

Warp readingMatching mold temperature setBatch disposition
≤0.70 mmLid 68 °C / side walls one grade higherRelease directly
0.71–0.90 mmLid 68 °C / side walls at baselineRelease after per-shell recheck
>0.90 mmAny grade mixed across circuitsWhole batch back to trial record

The value is mold temperature zoning, switchover and cooling time lining up, not one isolated temperature. Kexin New Materials (Guangdong) Co., Ltd. benchmarks this shell against IP67 and a stacking rig by method only, writes no certificate numbers, and keeps figures such as 20 kg loading or 4100 cycles on the structural side; Military injection molded container source factory OEM hands the contractor the card with three warp grades.

Conclusion

On the process card of Military injection molded container source factory OEM, lid flatness and groove evenness come down to 68 °C, 96% fill switchover and 26 s cooling, plus the two lines of third-shift warp ≤0.9 mm and groove spread ≤0.25 mm. Readings must hold steady from 7.6 kg empty to 20 kg loaded across 4100 open-close cycles, and a contract batch simply rechecks against the card.

Related Reading

Related Products