Quick answer: A Military night vision goggles shockproof plastic case sets the liner corner at R6 mm to hold slot shift under 0.7 mm and pad set under 0.35 mm.
Table of contents
- Liner slot corner radius on a Military night vision goggles shockproof plastic case
- Rebound of the lid pressure pad
- Slot shift after six-face drops
- Pad residual set in cold rechecks
- Corner radius value for optical batches
- FAQ
1. Liner slot corner radius on a Military night vision goggles shockproof plastic case
How far a slot moves after a drop depends on how much impact the corner radius spreads, with the lid pad carrying what is left. A Military night vision goggles shockproof plastic case sets the liner locating-slot corner at R6 mm, a value measured band by band on a 1.2 m / 6-face drop rig. The outer 500×370×195 mm, the cavity 435×310×140 mm and the wall of 4.1 mm fix shell stiffness; the radius governs where impact travels along the slot mouth. Too small a radius crowds force at the slot root, too large a one loosens the liner's grip. The empty case at 4.6 kg and the loaded case at 8 kg both went onto the rig, because a loaded liner takes more force.
Corner bands and pad readings are logged together on one record per radius step. A Military night vision goggles shockproof plastic case hangs both groups off a single radius band, and whether it ships is read from its shift over two consecutive faces.
Inspectors check the first column against the datum row by row.
| Corner band | Slot corner | Shift trend |
|---|---|---|
| Small | R6 mm minus tolerance | Larger |
| Nominal | R6 mm | ≤0.7 mm |
| Large | R6 mm plus tolerance | Looser |
Banding logs readings only; release comes later.
2. Rebound of the lid pressure pad
Beyond the impact the radius takes away, the lid pad absorbs the remaining displacement. This 10 mm pad presses on the liner's upper edge, compacts at impact, then pushes the slot back by rebound. A Military night vision goggles shockproof plastic case asks not for the hardest pad but for residual compression of ≤0.35 mm after rebound: press too hard and the slot deforms, rebound too little and the position is lost.
Rebound is not even across the lid. Two latches at 350 N each pull it down, so the ends compact more than the middle and each face sees a different clamping force. Fixed points on the lid give pad thickness after each drop, and the before-after difference gives rebound.
A single sealing ring at 18% compression shares the closure stroke with the pad, and the datum marks the two travels separately. IP66 is listed as a benchmark item, not a grade obtained.
3. Slot shift after six-face drops
Dropping six faces in turn reveals slot movement better than one face. A Military night vision goggles shockproof plastic case measures slot shift face by face at 1.2 m / 6 faces, and the largest of the six must stay at ≤0.7 mm for the band to count as stable.
Six faces are logged separately, since averaging throws away direction; the table stacks them row by row.
| Drop face | Slot shift | Pad residual |
|---|---|---|
| Bottom and top | ≤0.7 mm | ≤0.35 mm |
| Two long sides | ≤0.7 mm | ≤0.35 mm |
| Two short sides | ≤0.7 mm | ≤0.35 mm |
Laying out the six faces has a second use: a high opposite pair usually means the radius did not spread force that way, not that the pad failed. Averaging the six smooths away that directional bias. A Military night vision goggles shockproof plastic case therefore keeps extremes per face and treats the mean as reference only.
4. Pad residual set in cold rechecks
After the room-temperature drops, the case goes into a −25 ℃ chamber for a second pass on pad residual set. In the cold the pad stiffens and rebounds more slowly, so the same radius band can leave more residual compression and the slot moves with it.
What the recheck watches is whether the ≤0.35 mm line still holds in the cold. We log room and −25 ℃ residuals side by side, and a cold end under 0.35 mm means the pad choice is adequate. After 3800 open-close cycles the pad loosens a little, so that figure is filed too, keeping life-related slack apart from the cold effect.
Cold recheck and room-temperature drop are two entries for the same liner at two temperatures. A Military night vision goggles shockproof plastic case locks the corner value only when both pass.
5. Corner radius value for optical batches
The corner value is the smallest band whose shift stays below 0.7 mm over two consecutive faces; larger radii are trend records left out of delivery. A Military night vision goggles shockproof plastic case writes this line at the foot of the card and uses it to place a liner batch into delivery or back to a tool correction and fresh banding.
Three reading groups hold the corner value up: corner band, six-face shift and cold residual. The closing checks sit together in the table.
| Shift value | Check item | Drawing datum |
|---|---|---|
| Two consecutive faces | Slot shift | ≤0.7 mm |
| Cold end | Pad residual compression | ≤0.35 mm |
| Nominal radius | Slot radius | R6 mm |
A Military night vision goggles shockproof plastic case writes the value into the datum, so delivery needs no re-drop of every piece. JUNZHIJIA keeps each batch's corner band, six-face shift and cold residual in the outgoing record, so a review checks item by item against those three groups.
Conclusion
A Military night vision goggles shockproof plastic case holds slot shift within ≤0.7 mm by making three accounts agree: the corner radius spreads most of the impact, the pad takes the remaining displacement, and the cold recheck confirms the margin does not shrink. The R6 mm radius, the 10 mm pad and the ≤0.35 mm residual set go into one datum, so inspection and review share one set of readings. Six-face shift and the corner value are filed together, which makes slot stability traceable after delivery.
Related Reading
- Foam-insert hard plastic case clearance
- IP ratings on waterproof hard plastic cases
- Camera hard plastic case applications
- Portable shockproof hard case for a 3D scanner
Related Products
- 8 Series — Gun Cases; Military Equipment Cases; Camera Equipment Cases; Drone Cases; Watch Cases; Knife Cases; First Aid Cases; Electronics Equipment Cases
- WL8-2812 PP Gun Case — model WL8-2812
- All protective cases and toolboxes: 7 series, 158 models