Quick answer: Outdoor first aid kit waterproof plastic box: 9 cells and twin seals stay dry after 30 min of rain, gasket compression over 2 mm after a 1.2 m drop.
Table of contents
- Outdoor first aid kit waterproof plastic box cells and blind-reach path
- 105-degree self-locking hinge torque setting
- Compression margin of the twin mouth seals
- Leak verdict under rain exposure
- Compression measurement after drop recheck
- FAQ
1. Outdoor first aid kit waterproof plastic box cells and blind-reach path
Outdoor first aid kit waterproof plastic box measures 540 × 390 × 230 mm outside and 475 × 325 × 175 mm inside; a 3.6 mm wall and the lid rim flange take the gap. Empty mass is 4.5 kg and rated load 8.2 kg, with handle and latch forces set against the loaded figure. Dividers split the base into 9 cells with no connecting gaps, and cell mouth height lets a gloved fingertip reach the floor in one pass.
A 105-degree angle parks the lid past vertical so the liner clears the cell mouths, and the self-locking hinge holds that angle once released. Cells sit in two rows with an empty band beside the handle: a gloved palm lands there first, then slides along a divider to the target cell. Outdoor first aid kit waterproof plastic box dividers are moulded with the base, with radiused roots so a fingertip is not caught at the mouth. Two reflective strips mark the lid rim. Two handles rated 400 N each and two latches rated 340 N each are logged separately.
2. 105-degree self-locking hinge torque setting
Torque on the 105-degree self-locking hinge is logged in two bands: a lifting peak and a static hold value after the lid stops. Outdoor first aid kit waterproof plastic box hinge seats share the 3.6 mm wall gauge, with a reinforcing ring around the pin bore.
Outdoor first aid kit waterproof plastic box torque is read on a rig and rechecked each round. Pin-to-bore clearance goes on the sheet; large clearance rocks the lid at 105 degrees. The −20 ℃ to 55 ℃ working band belongs to material selection, and the cold end records only torque drift.
| Field condition | Watch item | Pass value |
|---|---|---|
| 105 degrees | Rock-back | No drop |
| Low light | Strips legible | Outline clear |
| −20 ℃ | Hinge torque | Reading logged |
3. Compression margin of the twin mouth seals
The mouth carries twin seals on the lid rim flange and mouth step, with a cavity between. Outdoor first aid kit waterproof plastic box compression is read as the height the seal loses once the lid closes, and the criterion is a recheck after a 1.2 m drop still showing at least 2 mm.
Outdoor first aid kit waterproof plastic box readings are taken at four corners and the long-edge midpoint, and the smallest of the five is judged against the 2 mm floor. IP67 is written in only as a benchmark; the sheet carries measured compression and the before-after drop delta. Seal section is matched to the flange height of the 3.6 mm wall.
| Cell zone | Clearance item | Recheck item |
|---|---|---|
| Handle-side band | Band width | Landing drift |
| Two cell rows | 9 cells opening | Max-min delta |
| Divider roots | Radius | Drop cracks |
4. Leak verdict under rain exposure
Rain runs at 100 L/(m²·h) for 30 min with the lid closed and no opening midway. Outdoor first aid kit waterproof plastic box stays shut throughout; the shell is wiped dry before opening so surface water is not misread as a leak.
Only three places are judged: the lid rim flange, the cavity between the twin seals, and the inner mouth step. No seepage is recorded only when all three stay free of a water line; one trace sends the case back to recheck. Outdoor first aid kit waterproof plastic box uses the 8.2 kg load figure only as ballast for the drop recheck.
5. Compression measurement after drop recheck
After a 1.2 m drop the case is dropped once on each of six faces, then compression is measured back at the mouth. Outdoor first aid kit waterproof plastic box lists five readings before and after as two rows; a large delta triggers a check of the two 340 N latches.
Only a recheck at or above 2 mm is a pass, and Outdoor first aid kit waterproof plastic box flags the low corner on its own rather than scrapping the shell. Two handles rated 400 N each are rechecked after the drop for stress marks in the 3.6 mm wall. The hot end of the −20 ℃ to 55 ℃ band gets a separate soak, with compression measured once more at ambient.
| Compression value | Condition | Recheck item |
|---|---|---|
| 2 mm or more | Fresh closed | Smallest of five |
| 2 mm or more | After 30 min rain | Cavity water line |
| 2 mm or more | After 1.2 m drop | Before-after delta |
Conclusion
Outdoor first aid kit waterproof plastic box ties water tightness and drop survival to one shell. Nine cells with a 105-degree self-locking hinge set the reach path after opening; twin seals with a 2 mm compression margin set the mouth boundary. The 30 min rain reading and post-drop compression are logged apart and judged together. JUNZHIJIA checks each item by these methods.
Related Reading
- First aid case mouth seal structure
- Emergency kit case handle and latch specs
- Emergency response case lid opening angle
- Disaster supply case stacking design
Related Products
- 8 Series — Gun Cases; Military Equipment Cases; Camera Equipment Cases; Drone Cases; Watch Cases; Knife Cases; First Aid Cases; Electronics Equipment Cases
- WL8-2812 PP Gun Case — model WL8-2812
- All protective cases and toolboxes: 7 series, 158 models