Quick answer: An outdoor multi-purpose shockproof micro safety case keys eight parts into 6 mm pockets, 20% foam compression and an 8 N pull-out on each.
Table of contents
- Keying parts in a micro safety case
- Part weight and foam compression
- Pocket depth and pull-out force
- Lid pouch and the parts list
- Belt clip and carrying
- FAQ
1. Keying parts in a micro safety case
Keys and small tools knocking against each other is the sound this product exists to remove. At 0.32 kg for the whole case the energy is small, but corner against corner still freckles an anodised finish. An outdoor multi-purpose shockproof micro safety case keys every part so that nothing touches anything else.
In an outdoor multi-purpose shockproof micro safety case, keying means one orientation per part. The body measures 180×120×45 mm outside and 168×108×32 mm inside, so eight pockets are cut from the outline of what they hold, wide end out and narrow end in; a reversed part will not seat.
Three words need separating. The pocket is the cell one part occupies; the well is the recess cut at the bottom of that cell to the part's outline; the keyway is the narrow slot that admits only one orientation. Mix them and the drawing carries two competing depths, and the foam arrives either loose or impossible to load.
Keying also saves time at night. Eight parts, eight wells, loaded by feel without laying anything out to count.
2. Part weight and foam compression
The foam in an outdoor multi-purpose shockproof micro safety case is 25 kg/m³ closed-cell EVA, carrying about 32–40 kPa at 25% compression. That suits parts from 20 g to 180 g: lighter ones refuse to stay put and roll in the pocket, heavier ones fight on the way in and worse on the way out.
Compression sits at 20%. Under 15% the part rattles and the wall takes the drop instead of the foam; over 30% the set grows and the pocket slackens within three months. ASTM D395 Method B, 70 °C for 22 h, keeps reusable inserts under 20% set, which pairs neatly with a 20% assembly compression.
| Part weight | Compression | Pull-out | Note |
|---|---|---|---|
| 20–50 g | 15% | 4 N | Wall locates it |
| 50–120 g | 20% | 8 N | Normal band |
| 120–180 g | 25% | 12 N | Needs a finger notch |
With mixed loads, set the rate by the heaviest part and shim the rest. Do it the other way and the heavy part crushes its well, the foam never recovers, and the other seven pockets start to move as well.
3. Pocket depth and pull-out force
In an outdoor multi-purpose shockproof micro safety case a 6 mm pocket is the compromise at this size. Under 4 mm the part jumps out on a drop; over 8 mm fingers cannot grip it and the case has to be tipped. At 6 mm with 20% compression, roughly 60% of the part stands proud of the foam.
Pull-out is specified at 8 N and read off a force gauge: pinch the part, pull straight up, take the peak as it leaves the well. Under 5 N it falls out in transit, over 12 N gloves cannot manage it. 8 N is about the effort of lifting 800 g, which a fingertip repeats reliably.
A 1 mm chamfer at 45° on the pocket edge drops that peak by roughly 2 N. Without it the square edge turns the force into a spike the hand feels as a snag.
| Pocket depth | Held at 1.2 m drop | Removal | Verdict |
|---|---|---|---|
| 3 mm | Jumps out | Easy | Unusable |
| 6 mm | Held | 8 N | Adopted |
| 9 mm | Held | Must tip out | Rejected |
4. Lid pouch and the parts list
The lid of an outdoor multi-purpose shockproof micro safety case carries a 0.1 mm film pouch for the list card, a spare fuse and a coin. It sits in a 4 mm recess so the pouch face clears the foam by 2 mm when the lid closes.
The pouch must not sit above a pocket. A 3 mm bulge pushes on the part opposite, and the latch force then arrives through the pouch as load nobody calculated. Offset it to the short side of the lid instead.
The card is 60×40 mm with eight lines, one per pocket. Its job is not record keeping but making an empty pocket visible at a glance, so nobody has to spread eight parts across a table.
5. Belt clip and carrying
The case weighs 0.32 kg and the clip is rated 15 kg, a factor of 47 that looks wasteful until you consider the drop. At 1.2 m the clip sees tens of times its static load at the instant of impact, and a micro safety case is carried far more often than it is set down.
The clip is a 25 mm webbing loop with a PA66 body and 1.2 mm spring wire. Webbing sits closer to the hip than a metal hook, swings less on the walk, and neither digs in at low temperature nor snags tent fabric.
The body is copolymer PP: notched Izod 4–15 kJ/m² at 23 °C, down to 2–4 kJ/m² at -20 °C. That cold knee is why corners carry R3 and the wall tapers from 2.5 mm to 1.8 mm instead of stepping.
Drop testing runs six faces and four corners at 1.2 m from -20 °C, where PP keeps about a third of its room-temperature toughness. A pass at 23 °C proves very little for an outdoor multi-purpose shockproof micro safety case.
Conclusion
Three numbers settle the design of an outdoor multi-purpose shockproof micro safety case: whether 20% compression survives the heaviest part, whether 8 N of pull-out survives chamfers and gloves, and whether a 15 kg clip survives a -20 °C drop. Fail any one on compression, pull-out or clip load and the specification is void.
Pull-out is the one that slips through on an outdoor multi-purpose shockproof micro safety case, because it is felt in the hand rather than written on the drawing. The same pockets, filled with foam 3 kg/m³ off density, will read 6 N or 11 N while looking identical. Put compression and pull-out on the incoming sample sheet, and the argument stops being about feel.
This article discusses only the container (case body) side of specifications and design intent, and does not cover any handling, loading or use of the contents.
Related Reading
- How much of a case cavity is actually usable
- Small hard cases against cartons for e-commerce
- Choosing a small IP68 dustproof hard box
- Structural needs of an emergency survival gear box
Related Products
- 8 Series — Gun Cases; Military Equipment Cases; Camera Equipment Cases; Drone Cases; Watch Cases; Knife Cases; First Aid Cases; Electronics Equipment Cases
- WL8-2812 PP Gun Case — model WL8-2812
- All protective cases and toolboxes: 7 series, 158 models