Quick answer: A Precision balance scale portable shockproof case holds level first: four M8 feet reach 0.1 mm/m and an 8 mm pad floats a 120 mm pan cavity.

Table of contents

  • What Level Means on a Precision balance scale portable shockproof case
  • Levelling Feet and the Bubble Seat in the Base
  • Floating the Pan Cavity
  • Re-levelling After a Move
  • The Fixed Values a Metrology Team Records
  • FAQ

1. What Level Means on a Precision balance scale portable shockproof case

A Precision balance scale portable shockproof case is a moving bench, not packaging. Readability of 0.1 mg holds only while the load sits vertically on the sensor, and a tilt of 0.1 mm/m is about 0.006 degrees. Across the 430 mm floor that lifts one end just 0.043 mm above the other: invisible, and enough to move the last digit.

The shell measures 430 x 320 x 165 mm outside and 385 x 275 x 125 mm inside, with a 3.9 mm wall in PP copolymer at 1.5 to 2.5 percent shrinkage. Ribs pull the floor into ripples during cooling, so 24 h after ejection a dial gauge sweeps three points per edge. Depth loses the 3 mm the lid liner takes up, leaving 122 mm clear.

A Precision balance scale portable shockproof case on an uneven floor turns four feet into an error patch. At the end of the thread nothing is left to adjust.

At minus 10 degrees PP loses about thirty percent of its impact strength, and a base dropped off a tail-lift splits at a rib. Short ribs and open corners spread that load better than a thicker floor.

2. Levelling Feet and the Bubble Seat in the Base

The Precision balance scale portable shockproof case uses four M8 feet at the corners. Coarse thread advances 1.25 mm per turn, a quarter turn is 0.31 mm, and that step matches the 0.1 mm/m reading, so a hand cannot jump the criterion. A 40 mm bubble seat is set into a removable panel and shares one plane with the feet; read it only when the bubble sits inside the inner ring.

Precision balance scale portable shockproof case dimension drawing, a red case shown closed and open with 315 mm, 260 mm and 128 mm dimensions marked.
Precision balance scale portable shockproof case dimension drawing, a red case shown closed and open with 315 mm, 260 mm and 128 mm dimensions marked.

Trim the long-edge pair first, then the short-edge pair, two passes in total; raising one foot pushes the opposite corner down. Each boss on a Precision balance scale portable shockproof case is thickened and carries a 20 mm threaded insert, so tightening load lands there instead of on the 3.9 mm floor.

Level settingFoot arrangementWhere it applies
Single-foot trimFour M8, one turnedBench already flat, residual inside 0.1 mm/m
Opposite pairLong-edge pair, counter-turnedOne end low by more than 0.3 mm
Full re-seatPanel removed and refittedFloor bowed, fix the shell first

3. Floating the Pan Cavity

A Precision balance scale portable shockproof case carries the cavity as a moulded well 120 mm across, and vibration reaches it only through wall and floor. An 8 mm pad sits under the flange, losing 2 mm at 25 percent compression and keeping 6 mm of travel, at about 71 kPa of stress. A gap between well and shell takes side impact on the shell first, and the lid liner touches only the rim.

Hardness, density and thickness belong on one drawing. EVA at 45 kg/m³ gives about 71 kPa at 25 percent compression, a 4 percent compression set after 24 h, and a 65 degree ceiling. Depth alone says nothing: equal thickness can carry half as much.

The well in a Precision balance scale portable shockproof case never touches the ground, so a knock stays a shell problem; impact must cross a recovering pad before reaching the rim.

4. Re-levelling After a Move

Set the case down, watch the bubble, then turn a foot. Reverse that order and the reference moves with the foot, so the figure describes the adjustment, not the bench.

Precision balance scale portable shockproof case dispatch area, six grey cases in two rows on a wooden pallet over green epoxy flooring.
Precision balance scale portable shockproof case dispatch area, six grey cases in two rows on a wooden pallet over green epoxy flooring.

A Precision balance scale portable shockproof case returns in three rounds: corners to the outer ring, long and short edges alternated, then three loaded readings inside 0.2 mg. Leave 10 min between rounds. From a 5 degree store into a 25 degree room, wall and cavity need 30 min, and the balance a 30 min warm-up at 45 to 65 percent RH.

The shell is rated to IP65: a 6.3 mm jet at 12.5 L/min for 3 min, covering rain and washdown, not immersion.

Feet face down in transit. At 2.8 kg it is lifted one-handed, and handle mounts are ribbed for twice that static weight.

Re-levelling roundActionPass figure
Round oneFour corners trimmedBubble clear of outer line
Round twoLong and short edges alternatedBubble centred at 0.1 mm/m
Round threeThree loaded readingsIndication within 0.2 mg

5. The Fixed Values a Metrology Team Records

Handover for a Precision balance scale portable shockproof case carries three lines: foot position as exposed thread height, bubble position as the ring it lands in, deviation as the worst of three loaded readings.

The level setting is the simplest structure holding 0.1 mm/m after three rounds; anything lighter is a temporary prop.

Cycling is a separate account. The design closes 3,400 times with two latches at 270 N each pressing the lid rim, and once that rim deforms the floor follows. The checking bench is a cast plate on four supports, so the case touches it only at the feet; a dial gauge sweeps five points.

Deviation readingTriggerAction
Inside 0.1 mm/mAfter three roundsRelease, record foot position
0.1 to 0.3 mm/mA foot at end of travelOpen panel, check flatness
Above 0.3 mm/mFloor bowed by latch forceReturn the shell, re-make the base

Conclusion

The level account for a Precision balance scale portable shockproof case has three layers: four M8 feet bring the bench to 0.1 mm/m, a 120 mm cavity rides an 8 mm pad, and three rounds of re-levelling pull the indication back inside 0.2 mg. Lose one layer and the other two cannot cover it. Measure floor flatness first, then argue about pad density, and look at the finish last.

Related Reading

Related Products