Quick answer: Long-Term Military Equipment Storage Case pairs a 26 mm base rib with 8.5 mm lugs to hold four-tier deflection under 1.10 mm after 168 h at 90 kg.
Table of contents
- Base Rib Height in Long-Term Military Equipment Storage Case
- Depth of the Stacking Locator Lugs
- Base Deflection After Seven Days Under Four Tiers
- Lid-Edge Mismatch After Unloading and Remeasuring
- Locking the Rib Height for a Warehouse Batch
- FAQ
1. Base Rib Height in Long-Term Military Equipment Storage Case
Four cases stacked for seven days answer one question first: how far the base sags, how far the lid edge shifts, and the rib height with the locator lugs give that answer. Long-Term Military Equipment Storage Case starts from a 700×480×300 mm shell with a 630×415×225 mm cavity and a 5.0 mm wall.
Stacking creep is not a single squeeze but a week-long load under which the base gives way a little at a time. Ribs run along the long side and split the panel into short spans, and shorter spans slow the creep. A shallow rib leaves one long span, so the 90 kg load falls on the wall roots and drags the lid edge out of square. One mould was trialled at 22 mm, 26 mm and 30 mm rib heights with the lug depth held at 8.5 mm and other dimensions unchanged. Three points are taken on each side of a rib and the deepest is logged for that tier. The drawing carries a tolerance band, so out-of-band samples are pulled before the rig.
| Rib height tier | Rib height | Lug depth | Base datum before load |
|---|---|---|---|
| Low | 22 mm | 8.5 mm | 0.00 mm |
| Middle | 26 mm | 8.5 mm | 0.00 mm |
| High | 30 mm | 8.5 mm | 0.00 mm |
All three rows begin at 0.00 mm; Long-Term Military Equipment Storage Case zeroes the datum so the difference opens up only after 168 h.
2. Depth of the Stacking Locator Lugs
The lugs are raised ledges at the lid corners where the base above sits; their 8.5 mm depth decides whether a four-tier stack drifts. Long-Term Military Equipment Storage Case checks lug depth and rib height as a pair: the rib stops the base sagging, the lug stops tiers sliding, and changing one alone wastes both.
With lugs too shallow, the base creeps along the lid under 90 kg and the upper tiers drift, so slip folds into the base deflection; with lugs too deep, the lid edge is propped open and the seal seam loads unevenly. Four latches, each at 440 N, hold the lid down; two gasket rings compressed 22% close the rim. Both are rig settings, booked on a line of their own.
3. Base Deflection After Seven Days Under Four Tiers
The rig squares four cases from one batch, sets 90 kg of ballast on top, and leaves the stack undisturbed for 168 h before measuring the bases. Long-Term Military Equipment Storage Case watches the late slope of deflection: a base still sinking near the end means the ribs have not held the creep, so readings are ordered by interval.
| Hold interval | Inter-tier load | Low / Middle / High deflection |
|---|---|---|
| 0 h | 90 kg | 0.00 / 0.00 / 0.00 mm |
| 72 h | 90 kg | 0.86 / 0.61 / 0.44 mm |
| 168 h | 90 kg | 1.34 / 1.02 / 0.79 mm |
At 72 h the three tiers sit within 0.9 mm and the low tier only crosses 1.10 mm in the second half; by 168 h the 22 mm tier at 1.34 mm is out, the 26 mm tier at 1.02 mm just holds, and the 30 mm tier at 0.79 mm has most margin. Long-Term Military Equipment Storage Case fixes only the 168 h row as the criterion.
4. Lid-Edge Mismatch After Unloading and Remeasuring
The 90 kg ballast is not judged the moment it comes off: the shell rebounds first, then the offset between lid edge and opening is measured, separating recoverable creep from permanent set. Long-Term Military Equipment Storage Case sets 0.48 mm as the lid-mismatch ceiling, since a small deflection that does not spring back means the wall roots have taken a residual bend.
| Deflection reading | Tier | Lid mismatch after unload | Disposition |
|---|---|---|---|
| 1.34 mm | Low | 0.62 mm | Single-tier circulation |
| 1.02 mm | Middle | 0.46 mm | Keep, pending the fixed value |
| 0.79 mm | High | 0.31 mm | Keep, but not the leanest |
The low row at 0.62 mm fails both columns and leaves the warehouse batch; the middle 0.46 mm and high 0.31 mm stay inside. Long-Term Military Equipment Storage Case keeps remeasure and loaded readings side by side per tier, and the mismatch never rewrites a deflection figure.
5. Locking the Rib Height for a Warehouse Batch
The rib height is fixed at the shallowest tier whose deflection at the one hundred and sixty-eighth hour still stays within 1.10 mm; anything shallower is reassigned to single-tier circulation.
That narrows the choice to the middle 26 mm tier: at 1.02 mm after 168 h it just holds the line yet uses less material than the 30 mm high tier, so drawing, rig log and inspection sheet all lock to it. Long-Term Military Equipment Storage Case gathers the creep readings into a batch card, noting the 8.8 kg empty shell and 22 kg of ballast on its header.
JUNZHIJIA treats IP67 as a benchmark, not a certificate in hand; the card carries no certificate number or claimed grade. The 4 tiers / 168 h, the 90 kg stack load and the 0.48 mm mismatch come off three rigs with separate raw logs. Kexin New Materials (Guangdong) Co., Ltd. plans the run from this card, and the warehouse batch stays as written once 26 mm is fixed.
Conclusion
Long-Term Military Equipment Storage Case ends on a 26 mm rib and an 8.5 mm lug, measured against 1.10 mm deflection and 0.48 mm mismatch after 168 h under four tiers and 90 kg. A shallower rib lets the base sag first, a shallower lug lets the tiers slide first. JUNZHIJIA sets the rib height from the post-unload mismatch, with base, inter-tier and seal booked apart.
Related Reading
- Long-Term Storage: Stacking Without Warping
- Storing Cases: Temperature, Humidity, Stacking
- Case Warehouse Storage: Stack Height, Pallets and Aisle Width
- Military Equipment Case Purchasing Checklist
- Military Protective Case Cost Factors
Related Products
- 8 Series — Gun Cases; Military Equipment Cases; Camera Equipment Cases; Drone Cases; Watch Cases; Knife Cases; First Aid Cases; Electronics Equipment Cases
- WL8-2812 PP Gun Case — model WL8-2812
- All protective cases and toolboxes: 7 series, 158 models