Quick answer: Military Case Customization Buying Guide sets a 45 mm scan pitch and 1.2 mm foam allowance to keep cavity deviation under 0.65 mm at CMM review.
Table of contents
- Scan Sampling Pitch in the Military Case Customization Buying Guide
- Foam Fit Allowance
- Cavity Deviation After First-Article CMM Review
- Slot Fit Rate on Trial Assembly
- Locking the Allowance for a Custom Batch
- FAQ
1. Scan Sampling Pitch in the Military Case Customization Buying Guide
How far the drawn cavity lands from the first article shows up once the CMM sweeps it: pitch and allowance settle it together. Military Case Customization Buying Guide fixes a 45 mm pitch, the probe dropping a point every 45 mm along a 545×370×175 mm cavity, with a denser pass at slot corners. At 20 mm a scan eats half a shift and the cloud is too large to align cell by cell; at 80 mm a corner flattens into a straight line. 45 mm resolves the corner without slowing review, so it opens the scan card.
A 610×430×240 mm shell with a 4.6 mm wall leaves only that 545×370×175 mm cavity, fixing the foam volume once the drawing is signed. The overlay gives each point a normal deviation; any value above 0.65 mm is flagged, and where flags cluster is where the next section tightens the allowance.
2. Foam Fit Allowance
The 1.2 mm foam allowance is read back from the cloud rather than preset as a round number: a small allowance bows the slot walls and lifts deviation, a large one leaves a gap and drops the fit rate. An uncut skin at the cell floor, with the 4.6 mm shell, holds the liner against sliding.
Here Military Case Customization Buying Guide keeps the point cloud and the cutting sheet apart: one governs the cavity outline, the other the cell sizes. A rig logs 4200 open-close cycles, checking walls and skin in blocks before the part reaches the CMM.
| Foam allowance tier | Allowance | First-article deviation |
|---|---|---|
| Tight | 0.8 mm | 0.72 mm |
| Middle | 1.2 mm | 0.61 mm |
| Loose | 1.6 mm | 0.44 mm |
The tight row at 0.72 mm crosses the 0.65 mm line; Military Case Customization Buying Guide wants the tier keeping fit rate without pushing deviation out, and the middle 1.2 mm sits just inside.
3. Cavity Deviation After First-Article CMM Review
A full sweep at 45 mm pitch precedes any comparison with the drawing. A deviation of 0.65 mm or less is the entry gate: a high fit rate means little if the cells bowed the cavity wall under a standing load. One deviation column per sampling index is tied to its own tier, and a missing index stays blank.
| Sampling index | Region | Peak deviation |
|---|---|---|
| Index 1 | Long slot floor | 0.58 mm |
| Index 2 | Slot corner | 0.65 mm |
| Index 3 | Cell mouth | 0.49 mm |
Index 2 sits on the line at 0.65 mm, where denser points matter; Index 1 and Index 3 stay below 0.6 mm. Military Case Customization Buying Guide halves the pitch at that corner and circles it on the review sheet.
4. Slot Fit Rate on Trial Assembly
Once the foam is trial-fitted, the fit rate is taken again to see whether the shape recovers. A fit rate of 96% or more is the keep line: small deviation that will not seat means the slot walls carry a permanent set. The refit rate and the first-article deviation are filed under one tier, with no figure borrowed across tiers.
The four 405 N latches load the lid, so slot walls must hold their shape; two gasket rings at 21% compression close the mouth and keep leak deformation out of the reading. A 6.4 kg bare shell and a 15 kg load are logged in a separate column.
| Deviation reading | Refit rate | Disposition |
|---|---|---|
| 0.44 mm | 91% | Fit too low, room-temperature liner |
| 0.61 mm | 96% | Keep |
| 0.72 mm | 98% | Deviation over line, out of batch |
The loose row fits at 91%, the tight row tops fit rate yet fails the gate; only the middle 0.61 mm / 96% row clears both, and Military Case Customization Buying Guide closes on it next.
5. Locking the Allowance for a Custom Batch
The allowance is fixed at the smallest tier whose deviation stays within 0.65 mm; tighter tiers leave the custom drawing. Only the middle 1.2 mm is left: it holds the line and its 96% fit rate clears the keep line, so drawing, cutting sheet and review sheet freeze to it. Military Case Customization Buying Guide turns cloud readings into a batch document with the 45 mm pitch, the corner rule and the 610×430×240 mm outer, 545×370×175 mm cavity and 4.6 mm wall entered.
IP67 stays a benchmark, not a certificate; the 21% compression, two rings and four 405 N latches are checked one by one, with no certificate number or test grade filled in. The 4200 cycles, the 45 mm pitch and the 96% fit rate lie on three separate rigs, each keeping its own trace. Once a tier is set, that drawing stays as issued.
Conclusion
Military Case Customization Buying Guide aligns a 45 mm scan pitch, a 1.2 mm allowance, 0.65 mm first-article deviation and 96% refit rate into one set that reads back against the drawing. A sparse pitch loses the corner first, a tight allowance lifts deviation first, and the middle tier comes from comparing three rigs with no answer preset. The deviation column fixes the allowance for Military Case Customization Buying Guide, with cloud, cutting and trial fit filed apart.
Related Reading
- Custom Case with Foam Insert Specs: Cavity, Layers, Drawings
- Custom foam insert case specs: 25-70 kg/m³, Shore A, ±1 mm
- What Factors Should a Custom Protective-Case Foam Insert Consider? A Complete Checklist Based on Equipment Shape, Weight, and Vulnerability
- Military Protective Case Cost Factors
- Military Field Deployment Case
Related Products
- 8 Series — Gun Cases; Military Equipment Cases; Camera Equipment Cases; Drone Cases; Watch Cases; Knife Cases; First Aid Cases; Electronics Equipment Cases
- WL8-2812 PP Gun Case — model WL8-2812
- All protective cases and toolboxes: 7 series, 158 models