The protection of the drone body is often valued, but accessories such as controller, propellers, aerial gear and video-link ground station are equally vulnerable in transit. The conclusion up front: a qualified drone accessory case must center on "item fixation, fragile-surface sinking, propeller anti-deformation, quick access", combined with waterproof dustproof shell and custom-cut lining, to systematically protect controller, propellers, aerial gear and ground station. This article covers drone controller cases, drone propeller cases, aerial gear cases, drone video-link ground station cases, drone controller boxes, drone propeller boxes and aerial gear boxes, providing parameters, standards and selection methods for procurement and implementation.
Drone accessories are irregular and valuable: the controller has screen and sticks, fears pressure and moisture; propellers are carbon or plastic, fear bend and crack; aerial gear has gimbal and camera, fears shock and scratch; the video-link ground station has antenna and display, fears bump and interference. A poorly designed accessory case can deform propellers, loosen gimbal or crack controller screen in one transit. Therefore the accessory case is not simple storage but a gateway of operation efficiency and asset protection. Whether a solo-pilot drone controller box or a film/inspection aerial gear case, it should be planned from structure, lining and sealing.
Table of Contents
- Protection Needs and Pain Points of Drone Accessories
- Design of Drone Controller Cases
- Zoning of Drone Propeller Cases
- Protection of Aerial Gear Cases
- Integration of Drone Video-Link Ground Station Cases
- Battery and Charging Accessory Management
- Case Material (PP/ABS)
- Three-Protection and Sealing (IP Grade)
- Cushioning Lining and Custom Cutting
- Transport and Air Check-in
- Moisture Control and Propeller Protection
- Drone Controller Boxes and Portable Forms
- JUNZHJIA Custom Capability and OEM/ODM
- Procurement Acceptance and Documents
- FAQ
Protection Needs and Pain Points of Drone Accessories
The pain points of drone accessories: irregular shapes and many accessories, ordinary boxes cannot fit or fit but rattle; controller screen and propellers have many vulnerable surfaces; field environments are complex, seaside salt spray, desert dust and rainforest humidity all threaten accessories; the video-link ground station also involves electromagnetic environment. The solution is to upgrade "storage" into "protection + fixing".
In protection grades, field accessory cases commonly use IP65-IP67 (GB/T 4208 / IEC 60529) against splash and short immersion; long-distance check-in references ISTA 3; lithium accessories flammability references UL94. For inspection, police and film teams, cases must also be light, quick-open and cabin-carryable, complementing the large cases of drone transport cases. Related industry drone carry can refer to the whole-machine solution of drone transport cases.
| Accessory | Risk | Focus |
|---|---|---|
| --- | --- | --- |
| Controller | Screen crack, damp | Screen sink, dry |
| Propeller | Bend crack | Orient, anti-press |
| Aerial gear | Shock scratch | Gimbal fix, surface |
| Ground station | Bump interfere | Antenna, EMC |
In field deployments, the sealing and cushioning of Drone Accessory Cases come first: referencing IEC 60529 and GB/T 4208 for the IP rating, IP65 suits dust and splash protection while IP67 is preferred for wet or submerged environments to keep the contents free from moisture and grit.
Drone Accessory Cases is often paired with Oil-Well Pressure Instruments & Pipeline Inspection Equipment Cases, for example a main unit with separate battery and accessory layers that protect the gear and speed field setup.
Design of Drone Controller Cases
The controller is the bridge between pilot and drone, containing screen, sticks, antenna and battery, most afraid of pressure, moisture and drop. Design essentials of a drone controller case: body wrapped in foam grooves so grip and screen bear no pressure; LCD sunk buffered to avoid screen pressure; antenna slot avoiding to prevent bend; battery compartment independent and insulated.
The drone controller box is the portable version for solo pilots, emphasizing compact, quick open and hanging. Whether case or box, paste controller list and checklist on inner lid, used with drone propeller cases and aerial gear cases to form an accessory system. For high-end screen controllers, lining reserves expansion (sunshade, bracket) space, never force-fit.
For impact resistance, Drone Accessory Cases should be designed to an IK rating per IEC 62262, with thickened rounded corners and metal latches; transit drops are evaluated against MIL-STD-810H Method 516.8, and experience shows the shell can survive multiple 1.2 m drops without cracking.
For shipping, add desiccant and a humidity card outside Drone Accessory Cases, especially for sea freight or humid regions; long-term storage follows the ISTA guidance on temperature-humidity cycling to avoid gasket aging and metal corrosion.
Zoning of Drone Propeller Cases
Propellers are the most deformable drone part: carbon props are stiff but brittle, plastic props flexible but easy to bend; compression or twist in transit destroys dynamic balance, increasing vibration or even flyaway after takeoff. The core of a drone propeller case is "single oriented, flat anti-pressure, soft partition". The common practice is an independent flat slot per pair of propellers, oriented by axis, not stacked, partition walls absorbing impact.
The drone propeller box is the portable version for spare props, emphasizing light and quick access. Folded props should be locked before slotting to avoid rebound damaging shell. Whether case or box, propellers must not share a slot under heavy objects. Related precision gear protection can learn from the shock lining thinking of precision instrument cases.
Vibration and transit reliability can be verified with the ISTA 3A/3E series of simulated shipping tests; for sensitive loads such as Drone Accessory Cases, custom-cut EVA foam that holds every item in place markedly reduces in-transit damage.
When standard grids cannot fit odd-shaped gear, custom-cut Drone Accessory Cases pays off; JUNZHJIA's OEM/ODM flow is sample, drawing, prototype and batch, with test files supplied and tooling on hand to shorten lead time.
Protection of Aerial Gear Cases
Aerial gear (gimbal camera, action camera, filters, video transmitter) is high value and precision; the aerial gear case core is "gimbal fixation + lens surface + accessory zoning". The gimbal contains brushless motor and attitude sensing; before transport lock gimbal and relax motor, lining avoiding latch position; lens and filter sunk soft partition, not pressured not scratched; video transmitter and cables separate slots with cable management.
The aerial gear box is the portable version for short-video and travel, emphasizing light. Whether case or box, screen and lens should have independent soft partition, never share slot with hard objects. For battery aerial gear, reserve battery compartment inside meeting insulation fixation, consistent with the battery handling of controller cases above. Film teams can combine the whole-set solution of film camera equipment cases.
Material choice for Drone Accessory Cases typically spans modified PP, ABS and PC: PP is light and shock-tolerant for frequent carrying, ABS offers good rigidity at moderate cost, and PC gives the highest impact strength at the expense of weight; flame rating can be specified to UL 94 V-1 or better for in-vehicle and cabin safety.
If Drone Accessory Cases carries lithium cells or energetic parts, give it a separate fire-resistant bay with labeling and ship per UN 38.3 and IATA rules for lithium batteries; like Detection Instrument Protective Cases: Gas, Water-Quality, Noise & Wind-Speed Meters, isolation and marking are key.
Integration of Drone Video-Link Ground Station Cases
The video-link ground station (receiver, antenna, display laptop, relay) is key for remote work; the drone video-link ground station case core is "antenna shape + display fixation + EMC balance". Antennas are fragile and bendable, independent slot relaxed to center; display laptop fixed like a laptop carry case, screen sunk; relay zoned with cable management.
Video-link involves wireless bands; if the case contains transceiver units, care about EMC to avoid mutual interference with other station devices; if necessary lining conductive or shell shielded. Ground stations often move by vehicle, cases should be stackable fixed and wheeled. Related communication test gear can refer to communication equipment cases transport protection. Outdoor work can combine the waterproof form of outdoor gear cases.
Liners commonly use high-density EVA or PE foam, CNC-cut to the actual part or drawing so each item sits in its own pocket. JUNZHJIA supports custom liners and OEM/ODM with brand-color printing, matched seals and test documentation for batch acceptance.
For field usability, Drone Accessory Cases should open one-handed even with gloves, with latches that resist accidental release; in designs such as Industrial Equipment Cases: Oil Exploration, Nuclear Inspection, Surveying & Rail Maintenance, quick access and loss prevention rank above looks.
Battery and Charging Accessory Management
Drone batteries, chargers, charging hubs and cables are high-frequency accessories; management core is "battery safety + cable + quick access". Batteries should be independent compartment, insulation divider, limit buckle to avoid colliding; multiple batteries not stacked, off in transport, interface cap in place; logic consistent with drone battery cases: upright, insulated, fixed, away from heat. Chargers and cables use mesh bag or cable channel to avoid tangling and pulling connectors.
Attach battery list and capacity label inside for power management; for self-drive, charging accessories can coordinate power with mobile power outdoor cases. Good battery management is both safe and improves field endurance and operation continuity.
Temperature and humidity control is an often-overlooked aspect of Drone Accessory Cases transport: passive insulation can use phase-change cold packs or an insulated bladder, and extreme temperature bands follow MIL-STD-810H Methods 501/502, with experience indicating structural stability from -20 C to +60 C.
To set the protection grade of Drone Accessory Cases, list the gear and the real duty (temperature, humidity, dust, drop, vibration), then match IEC 60529, MIL-STD-810H, ISTA, UL 94 and IK item by item rather than trusting marketing numbers.
Case Material (PP/ABS)
Accessory cases commonly use PP and ABS, or ABS+PC alloy. PP is tough, chemical resistant, cheap, low-temp, suitable for general and propeller cases; ABS high rigidity and good look, suitable for controller and aerial gear cases; PC strong and temp resistant, suitable for demanding video-link and ground station cases. Shell injection-molded one piece, corner thickening and stiffeners for life.
For large cases like ground station cases, bottom with forklift holes and stacking pins; for portable forms like drone controller boxes, reduce weight under strength, emphasizing carry and hanging. Material grade should be marked in acceptance documents.
| Material | Advantage | Limitation | Typical Use |
|---|---|---|---|
| --- | --- | --- | --- |
| PP | Tough, chem, low-temp | Avg rigidity | General, prop case |
| ABS | High rigidity, look | Avg temp | Controller, aerial |
| PC | Strong, temp | Costly | Video, station |
| ABS+PC | Compromise | Mid cost | General accessory |
For Drone Accessory Cases with electronic circuits, consider conductive gaskets and a metallized case for EMI shielding, assessed against the GB/T 17626 series for immunity so strong electromagnetic fields in the field do not disturb readings or comms.
Three-Protection and Sealing (IP Grade)
Three-protection means waterproof, dustproof and anti-corrosion. Seals are mostly nitrile or silicone rings embedded in flange under compression. To reach IP67, the ring uniformly compressed, no breakpoint, no debris. Seaside shooting controller cases should care about salt spray aging of seal, replace periodically.
Waterproof does not mean immersion. IP67 means no ingress at 1 meter for 30 minutes; long immersion needs IP68. If accessories fear moisture, combine desiccant and humidity card for "seal + moisture absorption" double insurance. Related sealing can refer to the general practice of sealed protective boxes.
At incoming inspection, Drone Accessory Cases should ship with third-party IP, IK and drop reports; check gasket continuity, even latch compression and liner fit item by item. Like Portable Diagnostic Equipment Cases: Handheld Ultrasound, Patient Monitor, Ventilator & Defibrillator, complete documentation eases warehousing and insurance claims.
Cushioning Lining and Custom Cutting
The cushioning lining decides whether accessories "shake, compress or collide". Common EVA, PE, PU, custom cutting CNC grooves by three-dimensional shape, embedding accessories into foam. For drone controller cases, drone propeller cases, aerial gear cases and drone video-link ground station cases, custom lining not only absorbs shock but also does "fixed management": each item one slot, missing known at a glance, improving field counting efficiency.
JUNZHJIA can customize CNC-cut foam lining according to your controller, propeller, aerial gear and ground station shapes, achieving precise wrapping of one slot per object, and support silk-screen and color. Existing cases can also order lining and seal kits separately to upgrade protection.
For site management, tag Drone Accessory Cases with an ID and a contents card, keep a master list with the supervisor, and reconcile against the card on departure and return; this mirrors the numbering system used by Fire-Fighting Equipment Cases & Rescue Forcible-Entry Kits and cuts loss rates.
Transport and Air Check-in
Air check-in limits accessory case size and weight, cargo hold has drop, stack and temp risks. Recommendations: single-case weight within two-people-lift or one-person-push; large cases with wheels and forklift holes; accessories fully fixed by lining to avoid sliding; lithium controllers, aerial gear and batteries insulated and fixed separately per air dangerous-goods rules with labels.
Cross-city work can reference ISTA 3 transport verification. Multi-case unified outer module for palletization, reducing loss risk. Valuable ground stations recommend cabin-carry or transport insurance.
For Drone Accessory Cases that is airdropped or flown at altitude, balance weight and ballast, add redundant latches and, where needed, a pressure-equalization valve to counter altitude-induced suction; related thinking appears in Earthquake Emergency Kits & Flood-Control Emergency Cases.
Moisture Control and Propeller Protection
Seaside and rainforest shooting, controllers and aerial gear fear moisture, managed by "seal + desiccant + humidity card"; propellers do not fear moisture but fear deformation, must be flat oriented, no pressure. Long storage propeller cases should take out batteries, wipe interior dry, put desiccant then close; propellers not cantilevered, end buffer columns.
For high-end gimbal cameras, attach humidity record card for asset management. Propeller deformation can be checked by light for twist, replace if found to avoid takeoff hazard. Related moisture logic is consistent with camera equipment cases.
To extend seal life, keep the silicone gasket of Drone Accessory Cases away from oil and prolonged UV, wipe it regularly and apply silicone grease; lubricate latch hinges and store the case slightly open to avoid crushing the gasket.
Drone Controller Boxes and Portable Forms
Solo pilots and short-video teams more often use portable forms like drone controller boxes, drone propeller boxes and aerial gear boxes: small, cabin-carryable, emphasizing quick open and hanging. The advantage of portable boxes is flexibility; the disadvantage is limited capacity, requiring selection of "one common set", leaving spares to large cases.
Whether case or box, interior insists on item fixation and fragile-surface sinking. Aerial gear boxes must also avoid sharing slots with hard objects. Bad weather can combine the waterproof form of outdoor gear cases. Related portable power can also refer to the battery safety logic of mobile power outdoor cases.
On size and stacking, choose Drone Accessory Cases with interlocking ribs and lateral stackability so vehicle or rack transport saves space and resists sliding; aligning the outline with Security Inspection Cases & Explosion-Proof Inspection Toolkits simplifies modular handling.
JUNZHJIA Custom Capability and OEM/ODM
For pilots, inspection and film organizations, JUNZHJIA provides integrated capability from case selection, lining customization to seal kit matching. We can customize CNC-cut foam lining according to your controller, propeller, aerial gear and ground station shapes, achieving one slot per object; support OEM/ODM color, silk-screen and structural modification by model; for export projects provide IP, flammability and transport related detection documents. Existing cases can also order lining and seal kits separately to upgrade protection.
Export Drone Accessory Cases must address RoHS, REACH and packaging directives, with flame and environmental declarations supplied in the case; JUNZHJIA can prepare market-specific compliance files to lower the buyer's customs and audit risk.
Procurement Acceptance and Documents
Documents recommended for drone accessory cases: material grade (PP/ABS/PC), IP grade declaration or report, lining layout drawing, drop/vibration records (large cases), flammability grade when powered, moisture description. The contract clarifies warranty, seal replacement cycle and spares. For high-value categories like ground station cases, trial in small batches before mass, observing lining and seal stability under real transport.
Mistake one: only look at capacity not fixation, propellers compressed and deformed in transit. Mistake two: treat "fits" as "protects", too large gap causing collision. Mistake three: ignore moisture, box directly after seaside/rainforest. Mistake four: battery and metal accessories mixed, short risk. Mistake five: not replace seals, ring aged still used as IP67. The methods in this article avoid these systematically.
The key to improve field efficiency is "listing + grouping". Each case corresponds to an accessory list and pre-flight check steps, take and count on-site by diagram, missing found immediately. Recommend "controller case + propeller case + aerial gear case + ground station case" as an operation unit moved together, ready at site with one click. With these, drone accessories change from "rummaging" to "ready to use", ensuring every safe flight.
Beyond the immediate protection function, the drone accessory case should be evaluated on total lifecycle cost. A cheaper case that cracks a latch on the first rough field day, or whose lining holds dust for a season, ends up more expensive than a robust case maintained for years. When comparing quotes, ask for the expected seal replacement interval, the availability of spare lining kits, and whether the shell can be repaired after a crack. For working pilots, these factors often outweigh a small upfront saving and belong in the purchase scorecard.
Many operators run shared kits that rotate between pilots or a fleet. For these, the case must support quick visual audit: a labeled lining where every slot has a part number lets the returning pilot confirm completeness in minutes. Adding a small damage-log sleeve on the lid, where users note any dent or fault, builds a history that protects both the gear and the next pilot. JUNZHJIA can pre-print such logs and part-number labels as part of the OEM/ODM service, so the kit arrives audit-ready.
Safety documentation matters for drone accessories because of lithium in controllers and aerial gear. A case supplied with an IP declaration, a lining layout drawing and a battery-safety summary strengthens both insurance and peace of mind. Keep a digital copy with the kit. For cross-border flights, the same documents answer questions about the contained equipment and help prove compliant transport of batteries as required by air carriers.
Climate adaptation is often overlooked. Cold environments make plastics more brittle and seals stiffer; hot environments soften adhesives and can warp thin-wall boxes. If your work spans seasons, choose a material grade rated for the full temperature band and verify the seal remains compliant at both ends. Desiccant capacity should also be sized for the humid leg of the journey, not just the storage condition.
A solo pilot benefits from one well-packed portable box they never have to think about; a team benefits from a system of matched cases that stack and share liners. Decide which model fits before buying, because retrofitting a team system from mismatched boxes is costly and error-prone. The modular approach pays off when a second pilot or a client job requires the same kit to split and rejoin without confusion.
Foam lining wears and eventually sheds; choosing a lining material that can be re-cut from stock, rather than a molded part unique to one case, keeps spares cheap and reduces waste. JUNZHJIA's CNC-cut lining supports this, since a new liner can be produced from the original drawing at any time. Pair it with a recyclable shell program where available, and the kit's environmental footprint stays manageable over a long service life.
Protection is only as good as the person closing the lid. A short onboarding that shows how to seat the seal, how to tension straps and how to read the humidity card prevents most field failures. Include this in the kit's quick-start card. Teams that train new members on the case itself report far fewer transit incidents than teams that treat the case as obvious.
A practical pre-flight checklist: confirm each item is in its slot, confirm the seal is clean and compressed, confirm propellers are flat and unstressed, confirm batteries are in their compartment and off, confirm the humidity card is green, and confirm the lid label matches the contents. Thirty seconds on this routine saves a grounded flight. The same checklist works whether the kit is a single portable box or a full case set.
For buyers comparing suppliers, request a reference build: a sample case packed with your actual accessories, photographed open and closed, with the lining drawing attached. This single exercise reveals more about real protection than any specification sheet, because it shows whether the vendor understood the fragile surfaces, the weight distribution and the access order you actually use in the field. Treat the reference build as the contract baseline, and volume orders will match it.
Battery discipline deserves a standing rule. Never store a battery inside a case that also holds a spark source, and never transport a power bank next to loose metal that could bridge its terminals. The case design supports this rule through separate compartments, but the rule itself must be taught. Teams that post the rule inside the lid see far fewer near-misses than teams that assume everyone knows it.
Propeller discipline is the other standing rule. Always transport propellers flat and unloaded, never bent against a hard object, because a micro-crack today becomes a mid-air failure tomorrow. The case design supports this through oriented slots, but the habit must be taught. Pilots who inspect propellers against light before each flight catch damage that no case can prevent.
Spare strategy should be planned at purchase, not after a failure. Identify the single most likely loss, usually a seal or a lining, and stock it before the first job. JUNZHJIA's CNC-cut lining means a replacement liner can be produced from the original drawing quickly, which keeps a damaged kit in service instead of waiting on a full case reorder.
Against soft bags, the hard shell of Drone Accessory Cases wins on crush resistance, water protection and security, suiting higher-value or long-stored Drone Accessory Cases; specify by equipment value and terrain rather than chasing the highest nominal rating.
Frequently Asked Questions
Q: What is the difference between drone accessory cases and ordinary storage boxes? A: The core difference is whether "item fixation, fragile-surface sinking, propeller anti-deformation, quick access" is achieved. Ordinary boxes just pile things, controller screen cracked, propellers compressed, gimbal scratched in transit. Accessory cases use custom-cut lining to embed each item, limit displacement, and sink buffer for screen and lens. In addition they must meet waterproof dustproof (GB/T 4208/IEC 60529), anti-vibration (ISTA) and flammability (UL94 with lithium). Therefore selection should start from accessory risk, not just capacity appearance.
Q: Why single oriented flat for drone propeller cases? A: Propellers are the most deformable drone part; carbon brittle, plastic easy to bend; compression or twist destroys dynamic balance, increasing vibration or flyaway after takeoff. Single oriented flat slot lets each pair oriented by axis, not stacked, partition walls absorbing impact. Folded props locked before slotting to avoid rebound damaging shell. Drone propeller box portable version also forbids sharing slot with heavy objects. Check twist by light, replace if found to avoid hazard. Therefore single oriented flat is the bottom-line design of propeller cases.
Q: How does a drone controller case protect the LCD? A: The controller screen and grip are most damageable; the case wraps body in foam so screen bears no pressure; LCD sunk buffered, screen contacts no hard object, no direct pressure; antenna slot avoiding bend; battery compartment independent insulated. Paste list and checklist on inner lid. The drone controller box portable version also does screen soft partition, not omitted for small. High-end screen controllers reserve sunshade bracket expansion space, force-fit damages shell. Thus controller ready at site.
Q: What special requirements for aerial gear cases? A: Aerial gear contains gimbal camera, action camera, filters and video transmitter; core is "gimbal fixation + lens surface + accessory zoning". Gimbal locked and motor relaxed before transport, lining avoiding latch; lens filter sunk soft partition not pressured not scratched; video transmitter and cables separate slots with cable management. Battery gear reserves battery compartment insulated. Aerial gear box portable version screen and lens independent soft partition, never share slot with hard. Film teams can combine film camera equipment cases whole-set for transit efficiency.
Q: How does a ground station case balance antenna and EMC? A: The video-link ground station contains receiver, antenna, display and relay; core is "antenna shape + display fixation + EMC balance". Antennas fragile, independent slot relaxed to center; display laptop fixed like laptop carry case, screen sunk; relay zoned cable managed. Involving wireless bands, transceiver units in case should care EMC to avoid mutual interference, if necessary lining conductive or shell shielded. Ground stations move by vehicle, should be stackable fixed wheeled. Related communication protection can refer to communication equipment cases, outdoor work combining outdoor gear cases waterproof form.
Q: How to safely manage battery accessories? A: Batteries, chargers and cables management core is "battery safety + cable + quick access". Batteries independent compartment, insulation divider, limit buckle to avoid colliding; multiple not stacked, off in transport, interface cap in place, logic consistent with drone battery cases: upright, insulated, fixed, away from heat. Chargers cables use mesh bag or cable channel to avoid tangling. Attach battery list and capacity label. Self-drive can coordinate with mobile power outdoor cases. Good battery management is safe and improves field endurance.
Q: Is custom lining worth it? A: Almost mandatory for drone accessories. Custom-cut lining (CNC groove by shape) triple value: shock (accessories embed limiting displacement), fixing (each item one slot, missing known), surface (screen and lens sunk without pressure). For precision accessories like drone controller cases, drone propeller cases, aerial gear cases and drone video-link ground station cases, lining directly decides protection. JUNZHJIA can open mold and cut by list or physical object, one slot per object, supporting silk-screen color; existing cases can also order lining separately. Compared with accessory damage and flight-stop loss, custom lining cost is minimal.
Q: What to note for air check-in of accessories? A: Cargo hold has drop, stack and temp risks. Single-case weight within two-people-lift or one-person-push; large cases with wheels forklift holes; accessories fully fixed by lining to avoid sliding; lithium controllers, aerial gear and batteries insulated and fixed separately per air dangerous-goods rules with labels. Cross-city work references ISTA 3. Multi-case unified outer module for palletization, reducing loss. Valuable ground stations recommend cabin-carry or insurance. With fixation, accessories ready at destination.
Q: How often to replace the seal? A: Rubber ring is consumable, check elasticity and cracks every six months, shorten to quarterly at seaside salt spray high-frequency field. Once hardens, cracks or compression unrecoverable, replace even if appearance intact, otherwise IP67 fails. Replace same-spec nitrile or silicone ring, clean flange before install. Desiccant humidity card replaced synchronously. Propeller cases need partial seal check for flat orient. With maintenance, a drone accessory case serves a typical value of multiple seasons without protection drop.
Conclusion and Related Reading
Drone accessory case selection should center on "item fixation, fragile-surface sinking, propeller anti-deformation, quick access", combined with waterproof dustproof shell, custom-cut lining and moisture management, to systematically protect controller, propellers, aerial gear and ground station. Doing protection before transit is far more cost-effective than flight-stop and repair after accessory damage.
Related Reading