Quick answer: Military Case Supplier Evaluation holds six batches to a 0.22 mm wall-thickness range, with an 11 s hold and a 7 °C mold-zone spread behind it.
Table of contents
- Injection Hold Time in Military Case Supplier Evaluation
- Mold Temperature Zone Spread
- Wall-Thickness Range Across Six Batches
- Weld-Line Offset After Sectioning
- Locking the Hold Time for an Approved Batch
- FAQ
1. Injection Hold Time in Military Case Supplier Evaluation
One drawing across several machines, six batches, one circuit of wall thickness: hold time and mold zoning show up entirely in the range. Military Case Supplier Evaluation starts from a 595×420×225 mm shell, a 530×360×170 mm cavity and a 4.4 mm wall, so how long pressure is held decides whether the melt packs that thickness evenly. Hold too short and the gate sinks while far corners stay short; hold too long and residual stress lifts the rim after ejection.
Trial the hold at 8 s, 11 s and 14 s with the zone spread kept inside 7 °C. The 8 s tier scatters most across the base, the 14 s tier raises ejection force, and 11 s sits between. Military Case Supplier Evaluation lets the measured range pick the tier, not a tidy round number.
| Hold time tier | Set duration | First-article range |
|---|---|---|
| Short | 8 s | 0.31 mm |
| Middle | 11 s | 0.18 mm |
| Long | 14 s | 0.24 mm |
All three rows start from 4.4 mm; the spread opens only once six batches are in.
2. Mold Temperature Zone Spread
Zone spread is the difference between cooling circuits, not one zone's absolute reading. Military Case Supplier Evaluation caps it at 7 °C: beyond that the melt fronts reach the seam out of step and a stray wobble enters the range. Eight rim temperatures are taken after the shot sets and the difference booked beside the hold time.
Zone spread and hold time are coupled. Ample hold with an uncorrected spread still lets a far corner freeze early; a flat spread with a short hold leaves the whole wall thin. Military Case Supplier Evaluation reads the pair on one rig so neither contribution is booked as a thickness fault. Four latches at 400 N and two gasket rings at 19% are booked apart from the molding readings.
3. Wall-Thickness Range Across Six Batches
Six consecutive batches, twelve pieces each, one fixed ring of points: Military Case Supplier Evaluation wants the curve the range traces by batch number, not one handsome figure. Points avoid the gate and seam; thickest minus thinnest gives a piece's range, and the largest of twelve becomes the batch range. Batches run one through six without a material change or machine adjustment. A first-article check only proves that piece could be tuned; over a run mold heat drifts and packing wanders, so the last batch is where the card shows whether it holds. The gauge is zeroed once per shift and the twelve stations are fixed on the drawing, so all six batches land on the same ruler.
| Batch number | Pieces drawn | Batch range |
|---|---|---|
| Batch 1 | 12 | 0.17 mm |
| Batch 3 | 12 | 0.19 mm |
| Batch 6 | 12 | 0.21 mm |
The sixth row matters most: a range still inside 0.22 mm at batch six means hold and zoning did not drift, while early passes and a late jump point to packing wandering with accumulated mold heat. Military Case Supplier Evaluation separates a one-off first-article check from continuous sampling for this reason.
4. Weld-Line Offset After Sectioning
The shell is then cut along the seam: Military Case Supplier Evaluation measures how far the weld line sits from its mark. Where two melt fronts meet they leave a line, and the further it strays the more out of step they arrived. The offset is capped at 1.6 mm, three points are taken on the cut face, and the largest deviation is kept.
A section check and a thickness check are different tasks: the range says how even one wall circuit is, the offset says how true the fronts met. The sheet sets both columns side by side and whichever crosses first sends the query back to its own process item. A rig logging 4400 open-close cycles keeps its pages apart from the molding readings.
5. Locking the Hold Time for an Approved Batch
The hold is fixed at the shortest tier whose sixth-batch range still stays below 0.22 mm; anything shorter stays off the approved card. That narrows to 11 s: at batch six it reads 0.21 mm, steadier than 8 s and without the ejection load of 14 s. Military Case Supplier Evaluation turns trial curves into a checkable card locked to that tier.
| Range reading | Hold tier | Disposition |
|---|---|---|
| 0.18 mm | 11 s | Approved |
| 0.31 mm | 8 s | Return for packing review |
| 0.24 mm | 14 s | Static sample record |
The 5.9 kg empty shell, 14 kg load, four 400 N latches and two 19% gasket rings belong to three ledgers, none vouching for the range. IP66 is a typical design target rechecked against a leak method, with no certificate number or claimed grade. What Military Case Supplier Evaluation puts on paper is 11 s hold, zone spread under 7 °C, six-batch range under 0.22 mm and offset under 1.6 mm.
Conclusion
The point of Military Case Supplier Evaluation is not a machine that looks right, but lining up an 11 s hold, a 7 °C zone spread, a 0.22 mm six-batch range and a 1.6 mm offset into one repeatable set. A short hold scatters the base, an unchecked spread freezes the far corner, and the middle tier holding the line is what the figures compare out to. Only when card, sampling sheet and section log keep separate books does the fixed value stand.
Related Reading
- Auditing a Case Factory: Eight Things to Check
- How Do You Evaluate a Protective Case Supplier? A Scoring System for Delivery and Quality
- Case Supplier Audit: Five Spots in a Case Factory Audit
- Military Protective Case Cost Factors
- Military Field Deployment Case
Related Products
- 8 Series — Gun Cases; Military Equipment Cases; Camera Equipment Cases; Drone Cases; Watch Cases; Knife Cases; First Aid Cases; Electronics Equipment Cases
- WL8-2812 PP Gun Case — model WL8-2812
- All protective cases and toolboxes: 7 series, 158 models