Boxknow
Two-Colour Moulding and Overmoulding: When Multi-Material Cases Make Sense
Moulding two materials into one part removes assembly steps and can improve grip, sealing and appearance. It also raises tooling cost and demands material compatibility, so the economics depend on volume and on what the second material actually buys.
Read Article →
Colour Coding and Visual Management for Case Fleets
Colour coding turns identification into a glance. Applied to a fleet of cases it reduces mis-picks, speeds loading and makes gaps obvious — provided the scheme is simple, documented and stable enough that everyone learns it.
Read Article →
RoHS and REACH Compliance for Protective Cases: What Buyers Should Ask For
RoHS restricts specific hazardous substances and REACH governs chemicals more broadly. For cases, compliance is a materials question that has to be evidenced by testing and declarations, not assumed from a supplier's assurance.
Read Article →
Where Protective Case Design Is Heading: Six Developments Worth Watching
The pressures shaping case design are practical rather than fashionable: payloads are getting more valuable and more delicate, sustainability reporting is becoming a procurement question, and fleets are large enough that small per-unit improvements compound.
Read Article →
Knife Collection Storage Case: Foam Choice, Humidity Control and Long-Term Care
For knife storage the foam matters as much as the shell. Closed-cell cross-linked polyethylene does not absorb moisture or oils, while cheap open-cell foam holds humidity against the blade. Control humidity, keep blades clean and dry, and avoid long-term storage inside leather sheaths.
Read Article →
How to Clean and Maintain a Protective Case: Shell, Gasket, Latches and Foam
Use mild dish soap and warm water, or 70% isopropyl alcohol for disinfection. Never use bleach, ammonia, acetone or abrasives, and lubricate the gasket with pure silicone grease only — petroleum jelly and WD-40 swell rubber and destroy the seal.
Read Article →
Injection Molding vs Rotational Molding: How Protective Cases Are Actually Made
Injection molding injects molten polymer into a steel tool under 500–2,000 bar, giving tight tolerances and fast cycles but expensive tooling. Rotational molding tumbles powdered resin in a heated mould at atmospheric pressure, giving seamless, uniform walls and cheap tooling for large parts at slow cycle times.
Read Article →
Custom Logo Printing on Protective Cases: 6 Methods Compared
Silk screen is cheapest for bold flat logos at volume, pad printing handles curves, laser engraving is permanent and needs no ink, UV digital printing needs no plates at all, IML fuses the label into the plastic, and mould-etched embossing never fades. Volume, surface and durability decide.
Read Article →
Tactical Equipment Cases: What MIL-STD-810, STANAG and IP67 Really Require
A tactical case is judged on documented compliance, not adjectives. The standards that matter are MIL-STD-810 environmental methods, NATO STANAG 4280 and 4340, UK Def Stan 81-41, ATA Spec 300 Category I, and an IP rating backed by a test report.
Read Article →
Export Packaging Compliance: ISPM 15, Labeling and Shipping Marks Explained
ISPM 15 requires all wood packaging thicker than 6 mm to be treated — heat treatment means a 56 °C core held for 30 minutes — and stamped with the IPPC mark. Plastic cases and crates are exempt from ISPM 15 entirely, which is one reason moulded containers simplify export.
Read Article →
Reusable Transport Cases in Logistics: Cost Per Trip, Nesting and Tracking
Returnable packaging is judged on cost per trip, not purchase price. A wood pallet costing 15 USD that lasts 20 trips costs 0.75 USD per trip; a 75 USD plastic pallet that lasts 1,000 trips costs 0.075 USD. Nesting and tracking decide whether the maths holds.
Read Article →
Inside a Drone Case Manufacturing Factory: Capabilities, Process and What to Verify
A drone case factory is judged on more than moulding capacity. Material control, tooling precision, interior engineering, testing discipline and the ability to hold tolerances across a production run are what separate a supplier that can make a sample from one that can hold a specification.
Read Article →