Boxknow
Cookware Polishing & Finishing Cases: Polishing Wheel & Component Protection
Polishing equipment case guide: bore-located wheels with end faces held clear, damp and crease prevention for abrasive belts, sealed chemical compartments, motor condensation control, dust and static boundaries, IP65/IP67 sealing, and GB/T 4857 plus ISTA validation.
Read Article →
Copper Smelting Parts Cases: Anode & Electrolytic Cell Component Protection
Selection guide for copper smelting parts cases: profile cradles that prevent anode plate bow, compartmented location for busbars and insulation parts, IP65/IP67 acid-mist sealing, ISTA and GB/T 4857 verification, and AQL acceptance.
Read Article →
Cutlery Die Cases: Forming Die & Edge Component Protection
Cutlery die case guide: compartmented tooth-form edge protection, hold-clear mirror cavity design with controlled clearance, sulphur-free and chlorine-free packaging, VCI and ISO 4406 cleanliness, GB 4806 food-contact boundaries, IP65/IP67 sealing, and GB/T 4857 plus ISTA validation.
Read Article →
Engine Valve & Valve-Train Cases: Valve & Tappet Component Protection
Selection guide for engine valve and valve-train cases: row locating holes that keep valve stems straight, one-per-compartment hydraulic lifter packing, multi-point camshaft cradles, ISO 4406 cleanliness, IP65/IP67 sealing and ISTA and GB/T 4857 verification.
Read Article →
EV Battery Tray & Mold Cases: Tray & Structural Component Protection
Selection guide for EV battery tray and mold cases: multi-point support for flatness and distortion control, relief for weld joints and sealing faces, aluminium corrosion and impact protection, IP65/IP67 sealing with pressure equalization and ISTA and GB/T 4857 verification.
Read Article →
Feed Pellet Mill Cases: Ring Die & Roller Component Protection
Feed pellet mill parts case guide: upright rigid location and end-face clamping for ring dies, die hole moisture and rust control, tooth-flank protection for press rollers, IP65/IP67 sealing, GB 17440 dust explosion boundary notes, and GB/T 4857 validation.
Read Article →
Flour Mill Parts Cases: Roller Mill & Sieve Component Protection
Flour mill parts case guide: V supports on roll journals with a free tooth surface, food-grade removable rust prevention for tooth grooves, flat moisture-controlled support for plansifter frames and screens, with GB 17440 dust explosion boundary notes and GB/T 4857 validation.
Read Article →
Foundry Ladle & Furnace-Front Cases: Ladle & Burner Component Protection
Selection guide for foundry ladle and furnace-front cases: non-mating-surface cradles, trunnion and tilting mechanism relief, full-area refractory support with moisture control, pre-packing heat and residue procedures, IP65/IP67 sealing and AQL acceptance.
Read Article →
Grain Dryer Cases: Fan & Elevator Component Protection
Grain dryer parts case guide: hub-located fan impellers with free blades, compartmented storage for elevator chains and buckets, sealed moisture control with desiccant against condensation, and protected moisture sensors, with GB 17440 dust explosion boundary notes.
Read Article →
Hardware Stamping & Die Cases: Press Die & Feeder Component Protection
Press die case guide: annular edge support and edge-clear locating, paired guide posts, feeder roller journal location, servo feeder cushioning and condensation control, VCI and ISO 4406 cleanliness, weight grading and lifting safety, IP65/IP67 sealing, and GB/T 4857 plus ISTA validation.
Read Article →
Kitchenware Mold & Stamping Cases: Mold & Punch Component Protection
Kitchenware mold case guide: cavity-up or cavity-down orientation, upright compartmented punch storage, paired guide posts, VCI and ISO 4406 cleanliness control, GB 4806 food-contact boundaries, IP65/IP67 sealing, and GB/T 4857 plus ISTA transport validation.
Read Article →
Rolling Mill & Roll Cases: Roll & Chock Component Protection
Selection guide for rolling mill and roll cases: V-block multi-point cradles that prevent self-weight bow, journal relief, compartmented chocks and oil-film bearings, IP65/IP67 sealing, ISTA and GB/T 4857 verification, and AQL acceptance.
Read Article →